General Power Tool Safety Warnings - Hitachi CS 36DL Instrucciones De Manejo

SYMBOLS
WARNING
The following show symbols used for the machine.
Be sure that you understand their meaning before
use.
CS36DL:
Cordless Chain Saw
Read all safety warnings and all instructions.
Do not use a power tool in the rain and
moisture or leave it outdoors when it is raining.
Only for EU countries
Do not dispose of electric tools together with
household waste material!
In observance of European Directive 2002/96/EC
on waste electrical and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility.
Read, understand and follow all warnings and
instructions in this manual and on the unit.
Always wear eye, head and ear protectors
when using this unit.
It is important that you wear the protective
clothing for feet, legs, hands and fore-arms.
Warning, kickback danger. Be careful of
possible sudden and accidental upward and/or
backward motion of the guide bar.
This chain saw is for use by trained tree
service operator only.
Chain oil fi ll
Chain oil delivery rate adjustment
WHAT IS WHAT? (Fig. 1)
A: Switch: Device activated by the fi nger.
B: Lock-off button: Button that prevents the accidental
operation of the trigger.
C: Chain brake: Device for stopping or locking the saw
chain.
D: Spiked bumper: Device for acting as a pivot when in
contact with a tree or log.
E: LED light: Light that illuminate the cutting edge.
F: Oil tank cap: Cap for closing the oil tank.
G: Oil sight glass: Window to check chain oil amount.
H: Front handle: Support handle located at or towards the
front of the main body.
I: Battery: Power source to drive the unit.
J: Rear handle (Top handle): Support handle located on
the top of the main body.
K: Hook: Tool for hanging the unit with rope etc.
L: Tension dial: Device for adjusting tension of saw chain.
M: Knob: Knob for securing tension dial and side cover.
N: Saw chain: Chain, serving as a cutting tool.
O: Guide bar: The part that supports and guides the saw
chain.
P: Side cover: Protective cover to the guide bar, saw
chain, clutch and sprocket when the chain saw is in
use.
(Original instructions)
Q: Charger: For charging the battery.
R: Oil feeder: Container for oil.
S: Chain case: Case for covering the guide bar and saw
chain when the unit is not being used.
T: File: Tool for sharpening saw chain.
U: Bolt: Bolt for fi xing the side cover in place.
V: Hexagonal bar wrench: Tool for loosening and
tightening the bolt.
WARNING
This chain saw (CS36DL) is designed especially for
tree care and surgery. Only persons trained in tree care
and surgery may use this saw. Observe all literature,
procedures and recommendations from the relevant
professional organization. Failure to do so constitutes a
high accident risk. We recommend always using a rising
platform for sawing in trees. Rappelling techniques are
extremely dangerous and require special training. The
operator must be trained in and familiar with the use of
safety equipment and working and climbing techniques.
Always use the restraining equipment for both the
operator and the saw.
GENERAL POWER TOOL SAFETY
WARNINGS
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in
electric shock, fi re and/or serious injury.
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
fl ammable liquids, gases or dust.
Power tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools.
Unmodifi ed plugs and matching outlets will reduce
risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts.
Damaged or entangled cords increase the risk of
electric shock.
5
English