Sears Kenmore 790.79992 Manual Del Usuario página 17

General Cleaning
(continued)
Unlike the standard gas range, THIS
COOKTOP IS NOT REMOVABLE. Do
not attempt to remove or lift the
cookton,
Note: The burner cap assembly refers
to all parts of the sealed burner unit
(burner cap, burner pan (some
models), trim ring (some models),
locating tab, burner base and
,electrode).
E
Burner Cap _
Locating Tabs_j 7,'_-1
B_rneer _ng
I . Slots
Electro
Trim Ring (some models)
or Burner Pan (some models)
to Cfear_ _.ne C,.,,_,_<.,.Jp
The cooktop is designed to make cleaning easier. Because the four burners
are sealed, cleanups are easy when spillovers are cleaned up immediately
To clean, wipe with a clean, damp cloth and wipe dry.
To Olear_ ti_e Co_sto_._i_ec$ We_i A_'eas_ B_me_ _ Ca_s ,&ssemb!y_
Trim Bi_sg (some tssodeis), Bct_i'l_" Pa_;s (sore® fs'_oc_ets} and
Burner Base
The contoured well areas, burner cap assembly, trim ring (some models),
burner pan (some models) and burner base should be routinely cleaned.
Keeping the burner ports clean will prevent improper ignitionand an uneven
flame. See instructions below.
To Clean the Contoured Well Areas
The contoured well is a recessed area located around each burner unit If a
spill occurs in one of the four well areas, blot up spill with an absorbent cloth
Rinse with a clean, damp cloth and wipe dry.
To Remove the Burner Cap Assembly
The burner cap assembly parts differ per model,, Your assembly will consist of _<2, _
one of the following combinations: burner cap and trim ring; burner cap and _<_a
burner pan; or burner cap, trim ring and burner pan Remove in the following _
order: (1st) burner cap, (2nd) trim ring and (3rd) burner pan. Do not operate '_? ....
the burners without the burner cap assembly in place. ;-_;_:]
To Clean the Burner Cap, Burner Pan (some models) and Trim Ring
(some models)
Use a soap-filled scouring pad or a mild abrasive cleanser to clean burner
caps, trim rings and burner pans.
To Clean the Burner Base and Gas Opening
The ports (or slots) around the burner base must be routinely cleaned, Use a
small-gauge wire or needle to clean small slots or holes .Use care to prevent
damage to the electrode. If a cleaning cloth should catch the electrode, it
could break or damage the electrode. If the electrode is damaged or broken,
the surface burner will not light.
Use caution when
replacing the burner cap so the
electrode is not damaged. This may
cause a delayed ignition or prevent the
burner from igniting..
_ Any additions, changes
or conversions required in order for
this appliance to satisfactorily meet the
application needs must be made by an
authorized Sears Service Center,
For proper flow of gas and ignition of the burner_DO NOT ALLOW SPILLS,
FOOD, CLEANING AGENTS OR ANY OTHER MATERIAL TO ENTER THE
GAS OPENING Gas must flow freely through the small hole in the brass
orifice for the burners to light properly., if the orifice gas opening becomes
soiled or clogged, use a small-gauge wire or needle to dean. ALWAYS keep
the burner cap assembly in place whenever a surface burner is in use°
To Replace the Burner Cap Assembly
Make sure the burner cap assembly is thoroughly dry before placing back on
the burner.
1. Lower burner pan (some models) into place around the burner base
2. Replace trim ring (some models).
3.. Find the locatingtabs on the burner cap and place in the locating slots in
the burner base. Make sure each burner cap is properly aligned and level.
4. Turn the burner on to determine if it will light. If the burner does not light
after cleaning, contact an authorized servicer. Do not service the sealed
burner yourself
17