Playing Discs; Play Buttons And; Pause Button; Stop Button - Rotel RCC-1055 Manual De Instrucciones

RCC-1055 CD Multi-Disc Changer

Playing Discs

Play Buttons and
9
Press the Play Button to play the disc indicated
in the Disc Display. The disc will begin playing
with Track 1, unless another track has been
selected before the Play button is pressed.
Unless one of the Repeat Play functions has
been selected:
• After the last track on discs 1 through 4 is
played, the next disc is selected and play
continues with track 1 of the disc.
• At the end of disc 5 disc play stops.
See the Repeat Play section for more infor-
mation.
Notes About MP3 Discs
The RCC-1055 can play discs recorded with
the MP3 (Mpeg1, Layer3) format. Either CD-R
or CD-RW discs may be used. The maximum
allowable number of folders on the disc is 255.
The maximum allowable number of files on the
disc is 999, with a maximum of 255 in any
folder. The bit rate for the disc must be between
32Kbps and 320Kbps. It is also possible to
play discs recorded with the Mpeg2, Layer3
and Mpeg2.5, Layer3 format.

Pause Button

-p
Press the Pause Button to temporarily stop
playing the disc. Press the Pause Button again,
or the Play Button, to resume playing the disc
at the same track and time.

Stop Button

0a
Press the Stop Button to stop playing the disc.
The disc will remain selected but the track
selection will go back to track 1.

Track Skip Buttons

=i
When a disc is not playing:
}
• Press the button to select the next track
on the disc. Press and hold the
to advance more than one track on the
disc.
{
• Press the button to select the previous
track on the disc. Press and hold the
button to go back more than one track on
the disc.
When a disc is playing:
• Press the
o track being played and begin playing at
the beginning of the next track on the disc.
Press and hold the
more than one track on the disc.
• Press the
ning of the track being played. Press and
hold the
one track on the disc.

Track Selection Buttons

(remote only)
To select a specific track on a disc, press the
corresponding Track Selection buttons. The
selected track immediately begins playing. To
select tracks higher than number 9 simply press
the appropriate buttons in quick succession.
For example, to select track 17, press the "1"
button then the "7" button.
NOTE: When the RCC-1055 is in Pro-
grammed Play mode, the Track Selection
buttons are used to select tracks to be added
to the program. See the Programmed Disc
Play section.

Search Buttons

(remote only)
Press and hold the
search a disc in the forward or reverse direction.
For the first five seconds the search speed will
be approximately four times normal playing
speed. After three seconds the search speed
will increase to approximately 20 times normal
playing speed. The sound volume is reduced
while the search function is being used. The
search function may be used when disc play
has been temporarily stopped with the Pause
function, however no sound is heard. The
Search function will not go past the beginning
or end of the selected disc.

About HDCD

HDCD discs are encoded with a high density
}
button data stream. During playback this high den-
sity data stream is decoded to a conventional
digital signal. This HDCD encode/decode
system greatly reduces the errors that are nor-
mally generated during the analog-to-digital,
{
and then digital-to-analog, conversions. The
HDCD system is automatically activated, and
the HDCD Indicator
HDCD disc is played.
}
button to skip the rest of
}
button to advance
{
button to return to the begin-
{
button to go back more than
d
[
] [
or buttons to quickly
®
3
3 lights, whenever an
10

Display Panel

The Disc Indicators A
the Disc Tray that have discs in them.
The Play Indicator B
is playing.
The Pause Indicator
has been temporarily stopped with the Pause
button.
The Disc Selection Indicator
the number of the disc currently selected. If the
Remaining Disc Playing Time display option
has been selected the Disc Selection Indica-
tor changes to a "–". See the Time Display
section.
The Track Indicator I
that is selected, the total number of tracks on
the disc, or the number of tracks that remain
on the disc. See the Time Button section.
One of the Repeat Play Mode Indicators
will light if one of the repeat play options has
been selected. See the Repeat Play Button
section for more information.
The Random Play Indicator
of the random play options is being used. See
the Random Play section.
The Program Play Indicator
the track programming function is activated.
See the Programed Play Section.
The Intro Scan Indicator
Intro Scan feature is activated. See the Intro
Scan section.
One of the Total/Each/Remain Time Indicators
J will light indicating what is shown in the
Time Display. See the Time Display Section.
The Time Display K shows either the total play-
ing time of the disc that is selected, the amount
of time the current track has been playing, the
remaining playing time of the current track, or
the remaining time of the disc that is playing.
See the Time Button section.
5
shows the positions in
is lit whenever a disc
C is lit when disc play
typically shows
H
shows either the track
F
E is lit when one
D lights whenever
G is lit when the