Ir Remote Control; Button Function; Wireless Footswitch - IMG STAGELINE FXBAR-5SET Manual De Instrucciones

ENTER again and then adjust the motor
speed ( ... ) .
7) For the music-controlled programs,
turn up the control MICROPHONE SENSI-
TIVITY until the FXBAR-5SET responds to
the music as desired . When the volume
of the music system is changed, readjust
the control accordingly . If there is no op-
timum music control although the control
has been turned up very far, increase the
volume or reduce the distance between
the speakers and the FXBAR-5SET .
After 5 seconds, when no sound
(music) has been registered, all units will
switch off their light beams . As soon as
sound is registered again, they will switch
them on again .
8) To select another mode, start with step 1
again .
System Settings
MENU /
ENTER
Spotlight /
Derby Light
Configuration
Function and example
MENU refer to chapter 6.1
E
M
Wireless
Footswitch
Mode
E
M
Reset
ENTER
3s
MENU
Test
30 s
M
MENU
Auto-off Feature
for Display
(after 30 s)
E
M

5.1.1 IR remote control

1) Before operating the re-
mote control for the first
time, remove the protec-
AUTO MUSIC ON/OFF
tive film from the battery
holder . Thus, the remote
A B C
control is ready for oper-
1 2 3
ation .
4 5 6
If the remote control
is not used for a longer
7
8 9
period of time, remove
0 - --
the battery as a precau-
tion . It may leak and dam-
age the remote control .
2) The remote control will not work in DMX
mode or slave mode . In these modes, press
the button MENU on the controller first until
the display indicates ,
3) When pressing a button on the remote
control, always point the remote control
at one of the two IR sensors (7) (figure
on page 12) . Make sure that there are
no obstacles between the sensor and the
remote control:
Button Function
light beams on/off
ON/OFF
automatic programs
with all effects*
AUTO
music-controlled programs
with all effects*
MUSIC
A
spotlight/derby light programs*
B laser programs*
C strobe LED programs*
switchover between automatic
mode and music control for the
spotlight /derby light programs, laser
programs and strobe LED programs
(buttons A – C)
stop / start of program
colour mode: all spotlights and
derby lights emit light of the same
colour
Use the buttons to select the colours
one after the other .
speed of automatic programs
0 9
...
- -- no function
* Press the button again to go to the
next program number .
Replacing the battery
1) Push the latch of the battery holder to
the right (arrow 1) and pull out the holder
(arrow 2) .
1. 2.
2) Remove the discharged battery and in-
sert a new battery (3 V button cell, type
CR 2025) into the support, positive pole
facing upwards .
3) Push the holder back into the remote
control .
Please observe the note on disposal of bat-
teries at the end of the following chapter .

5.1.2 Wireless footswitch

AUTO MUSIC
1) Before operating the footswitch for the
first time, insert the 12 V battery provided,
refer to paragraph below .
2) Unfold the transmitting antenna of the
footswitch and the reception antenna (12)
of the controller and put both antennas in
a vertical position .
Make sure that the footswitch mode
is enabled (chapter 6 .2) . The footswitch
mode is enabled in the factory and after
or .
reset .
3) Use the switch "I " on the rear to switch
on the footswitch .
4) The footswitch will not work in DMX mode
or slave mode . In these modes, press the
button MENU on the controller first until
the display indicates
5) The following functions can be controlled
with the footswitch:
Pedal Function
...
automatic show programs
AUTO
Press the button again to go to
...
the next program number .
music-controlled show programs
MUSIC
Press the button again to go to
the next program number .
colour mode: all spotlights and
derby lights will emit light of the
same colour
COLOR
Press the button again to go
to the next colour: white – red
– green – blue – yellow – cyan –
purple – white etc .
BLACKOUT light beams on /off
Remember to switch off the footswitch after
operation to prevent unnecessary discharge
of the battery . If the footswitch is not used for
a longer period of time, remove the battery
as a precaution . It may leak and damage the
footswitch .
Inserting/Replacing the battery
1) Unscrew the battery compartment cover
on the lower side of the footswitch .
2) Replace the discharged battery .
3) Insert a new 12 V battery (type 23AE) as
indicated in the compartment .
4) Close the battery compartment and screw
on the cover .
Never put batteries in the household
waste . To protect the environment,
always take them to a special waste
disposal, e . g . collection container at
your retailer .
ANT
COLOR BLACKOUT
, or .
15