Aluminium Processing; Technical Data; Intended Use - Festool TS 75 EBQ Manual De Instrucciones Original

Sierra de incisión
Ocultar thumbs Ver también para TS 75 EBQ:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 27
Measuring uncertainty allow-
ance
CAUTION
Operating noise
Damage to hearing
Use ear protection!
Vibration emission value a
directions) and uncertainty K measured in accor-
dance with EN 60745:
Vibration emission level (3-axles)
Sawing wood
Sawing metal
Uncertainty
The specified emissions values (vibration, noise)
– are used to compare machines.
– They are also used for making preliminary esti-
mates regarding vibration and noise loads during
operation.
– They represent the primary applications of the
power tool.
Increase possible for other applications, with other
insertion tools or if not maintained adequately. Take
note of idling and downtimes of machine!
2.4

Aluminium processing

When sawing aluminium, the following mea-
sures must be taken for safety reasons:
4

Technical data

Circular saw
Power
Speed (idling)
1
Max. speed
Inclination
Cutting depth at 0°
Cutting depth at 45°
Saw blade dimensions
Weight
Degree of protection
1.
Max. possible speed with faulty electronics.
K = 3 dB
(vector sum for three
h
a
< 2,5 m/s
h
a
< 2,5 m/s
h
K = 1,5 m/s
TS 75 EBQ,TS 75 EQ
1600 W
(110 V- Version: 13 A)
-1
1350 - 3550 min
-1
4400 min
0 - 47°
0 - 75 mm
0 - 56 mm
210x2,4x30 mm
6,2 kg
/II
– Connect the machine to a suitable dust extractor.
– Regularly remove dust deposits from the motor
housing.
– Use an aluminium saw blade.
– Close the viewing window/chipguard.
Wear protective goggles.
– When sawing panels, they must be lubricated
with paraffin but thin-walled profiles (up to 3
mm) can be sawed without lubrication.
3

Intended use

Plunge-cut saws are intended to be used for sawing
wood, materials similar to wood, plaster and ce-
2
ment-bonded fibre materials and plastics. When
2
fitted with special saw blades for aluminium of-
fered by Festool, these machines can also be used
2
for sawing aluminium.
Only saw blades with the following specifications
must be used: saw blade diameter of 210 mm; cut-
ting width of 2.4 mm to 2.6 mm; toolholder diame-
ter of 30 mm; blade core thickness of max. 1,8 mm;
suitable for speeds of up to 5000 rpm. Do not use
any abrasive wheel.
The machine is designed and approved for use by
trained persons or specialists only.
– Festool electric power tools must only be in-
stalled on work tables provided by Festool for
this purpose. If the tool is installed in another, or
self-made, work table, it can become unstable
and result in serious accidents.
The user is liable for improper or non-in-
tended use.
5
Operation
Unauthorised voltage or frequency!
Risk of accident
The mains voltage and the frequency of the pow-
er source must correspond with the specifica-
tions on the machine's name plate.
In North America, only Festool machines with
the voltage specifications 120 V/60 Hz may be
used.
Always switch the machine off before con-
necting or disconnecting the mains power
cable!
WARNING
TS 75
GB
15

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Ts 75 eq

Tabla de contenido