Transporting Your Washer; Reinstalling/Using Washer Again; Important - Maytag 3LMVWC100YW1 Manual De Uso Y Cuidado

WASHER CARE (cont.)
Begin procedure
1. Chlorine Bleach Procedure:
a. Open the washer lid and remove any clothing
or items.
b. Add 236 mL (1 cup) of liquid chlorine bleach
to the bleach compartment.
NOTE: Use of more liquid chlorine bleach than is
recommended above could cause washer damage
over time.
c. Close the washer lid.
d. Do not add any detergent or other chemical
to the washer when following this procedure.
e. Select the cycle recommended for cleaning the inside
of the washer.
f. Press the START/PAUSE/UNLOCK button to start the
cycle.
NOTE: For best results, do not interrupt cycle. If cycle
must be interrupted, press START/PAUSE/UNLOCK
once or twice [depending on model]. After the cycle has
stopped, run a RINSE and SPIN cycle to rinse cleaner
from washer.
Cleaning the Dispensers
After a period of using your washer, you may find some
residue buildup in the washer's dispensers. To remove
residue from the dispensers, wipe them with a damp cloth
and towel dry. Do not attempt to remove the dispensers or
trim for cleaning. The dispensers and trim are not removable.
If your model has a dispenser drawer, however, remove the
drawer and clean it before or after you run the Clean Washer
cycle. Use an all-purpose surface cleaner, if needed.
Cleaning the Outside of the Washer
Use a soft, damp cloth or sponge to wipe away any spills.
Use only mild soaps or cleaners when cleaning external
washer surfaces.
IMPORTANT: To avoid damaging the washer's finish, do not
use abrasive products.
NON-USE AND VACATION CARE
Operate your washer only when you are home. If moving, or
not using your washer for a period of time, follow these steps:
1. Unplug or disconnect power to washer.
2. Turn off water supply to washer, to avoid flooding due to
water pressure surge.

IMPORTANT:

To prevent damage to washer and personal injury, any
transport/installation of washer requires two-person handling.
WINTER STORAGE CARE
IMPORTANT: To avoid damage, install and store washer
where it will not freeze. Because some water may stay in
hoses, freezing can damage washer. If storing or moving
during freezing weather, winterize your washer.
To winterize washer:
1. Shut off both water faucets; disconnect and drain water
inlet hoses.
2. Put 1 L (1 qt.) of R.V.-type antifreeze in basket and run
washer on RINSE & SPIN cycle for about 30 seconds to
mix antifreeze and remaining water.
3. Unplug washer or disconnect power.

TRANSPORTING YOUR WASHER

1. Shut off both water faucets. Disconnect and drain water
inlet hoses.
2. If washer will be moved during freezing weather, follow
Winter Storage Care directions before moving.
3. Disconnect drain from drain system and drain any
remaining water into a pan or bucket. Disconnect drain
hose from back of washer.
4. Unplug power cord.
5. Place inlet hoses and drain hose inside washer basket.
6. Drape power cord over edge and into washer basket.
7. Place packing tray from original shipping materials back
inside washer. If you do not have packing tray, place heavy
blankets or towels into basket opening. Close lid and place
tape over lid and down front of washer. Keep lid taped until
washer is placed in new location.
IMPORTANT: Washer must be transported in the upright
position.

REINSTALLING/USING WASHER AGAIN

To reinstall washer after non-use, vacation, winter storage,
or moving:
1. Refer to Installation Instructions to locate, level, and
connect washer.
2. Before using again, run washer through the following
recommended procedure:
To use washer again:
1. Flush water pipes and hoses. Reconnect water inlet
hoses. Turn on both water faucets.
2. Plug in washer or reconnect power.
3. Run washer through Heavy Duty Regular cycle to clean
washer and remove antifreeze, if used. Use half the
manufacturer's recommended amount of detergent for a
medium-size load.
9