Guarantee And Technical Assistance; Safety Measures And Requirements - FAR KJ 45/S Instrucciones De Uso

Ocultar thumbs Ver también para KJ 45/S:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 36
INSTRUCTIONS FOR USE
I
INDEX

GUARANTEE AND TECHNICAL ASSISTANCE .............................. 12

SAFETY MEASURES AND REQUIREMENTS ............................... 12

TOOL IDENTIFICATION .................................................................. 13
GENERAL NOTES AND USE.......................................................... 13
MAIN COMPONENTS .................................................................... 13
TECHNICAL DATA .......................................................................... 13
AIR FEED ........................................................................................ 14
PRELIMINARY OPERATIONS ......................................................... 14
PLACING OF THE INSERT ............................................................. 15
WORKING PROBLEMS .................................................................. 16
CHANGE OF SIZE ......................................................................... 17
ADJUSTMENT OF TIE-ROD/HEAD UNIT ...................................... 18
TOOPING UP THE OIL-DYNAMIC CIRCUIT .................................. 19
MAINTENANCE ............................................................................. 19
DISPOSAL OF THE RIVETING TOOL ............................................. 19
GUARANTEE AND TECHNICAL ASSISTANCE
FAR riveting tools are covered by a 12-months guarantee. The period
of guarantee starts from the date of delivery specifi ed on the invoice
or delivery note.
The guarantee covers the user/buyer when the tool is bought
through an authorized dealer and only when it is employed for the
uses it was conceived for. The guarantee is not valid if the tool is not
used or maintained as indicated in the instruction and maintenance
handbook.
In case of defects or faults FAR S.r.l. undertakes only to repair and/or
replace the components it considers faulty.
SAFETY MEASURES AND REQUIREMENTS
CAUTION!!!
All the operations must be done in conformity
with the safety requirements, in order to avoid any
consequence for your and other people security and
to allow the best tool work way.
• Read the instructions carefully before using the tool.
• For all maintenance and/or repairs please contact FAR s.r.l.
authorized service centers and use only original spare parts.
FAR s.r.l. may not be held liable for damages from defective parts
caused by failure to observe what mentioned above (EEC directive
85/374).
• The tool must be used only by expert workers.
• A protective visor and gloves must be put on when using the tool.
• Use equipment recommended in the maintenance chapter to do any
maintenance and/or regulation of the tool.
• For topping up the oil, we suggest using only fl uids in accordance with
the features specifi ed in this working book.
• If any drop of oil touches your skin, you must wash with water and
alkaline soap.
12
GB
• The tool can be carried and we suggest putting it into its box after
using.
• The tool needs a thorough six-monthly overhaul.
• Repairing and cleaning operations must be done when the tool is not
fed.
• A safety balancer is suggested when it is possible.
• The tool is made so that acoustic pressure level continuous equivalent
weighted A is not more than 75 dB (A) where people works.
• If the noise level is more than 85 dB (A), you must use some hearing
protections (anti-noise headset, etc.).
• The workbench and the work surface must be always clean and tidy.
The untidy can cause damages to people.
• Do not allow unauthorized persons to use the working tools.
• Make you sure that the compressed air feeding hoses have the correct
size to be used.
• Do not carry the connected tool by pulling the hose. The hole must be
far from any heating sources or from cutting parts.
• Keep the tools in good conditions; do not remove either safety parts or
silencers.
• After repairing and/or adjusting, make sure you have already removed
the adjusting spanners.
• Before disconnecting the compressed air hose from the tool make sure
that there is no pressure in the hose.
• These instructions must be carefully followed.
ATTENTION! In case of strong impacts or accidental falls
the machine should be completely overhauled.
Date 11-2008
KJ 45/S
KJ 45/S
Revision - 00

Publicidad

Tabla de contenido
loading

Tabla de contenido