Kenwood KDC-BT742U Manual De Instrucciones página 7

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Category Item
MENU
"SECURITY SET"/
"SECURITY CLR"
"SKIP SRCH"
"DVC REGIST"
*
"S-DVC SELECT"
*
"PHONE SEL"
*
"SMS DOWNLOAD"
*
"SMS INBOX"
*
"VOICE TAG"
*
"VOICE RECOG"
*
"DEVICE DEL"
*
"DVC STATUS"
*
"PIN EDIT"
*
"AUTO ANS"
*
"MIC GAIN"
*
"NR LEVEL"
*
"SP SEL"
*
"CALL BEEP"
*
"BT F/W UPDATE"
*
"BEEP"
*
"CLOCK ADJUST"
"DISPLAY"
"DIMMER"
"IL EFFECT"
"DOT LINE"
"AMP"
Setting
Entry
Setting overview
Sets/Resets security code.
1 sec.
"0.5%"*/
Sets the ratio of skip performed with <Music Search for
"1%"/ "5%"/
iPod>.
"10%"
Register a Bluetooth device (pairing).
1 sec.
Allow registration of a special device that cannot be
1 sec.
registered normally.
Select a cell-phone subject to hands-free connection.
1 sec.
Download a short message.
1 sec.
Display the received short message.
1 sec.
Registers voice for voice recognition and voice to select
1 sec.
the Phone number category in Phonebook.
Calls by recognizing the registered voice.
1 sec.
Cancel registration of the Bluetooth device.
1 sec.
Display the status of the Bluetooth device.
1 sec.
Specify the PIN code required when registering this unit
1 sec.
using the Bluetooth device.
"OFF"/ "0S" –
Answer a call automatically after lapse of the preset time
"8S"* – "99S"
interval for automatic answer.
"–2" – "0"* –
Adjusts the sensitivity of the built-in microphone for a
"+2"
telephone call.
"–2" – "0"* –
Reduces the noises generated by the surrounding
"+2"
environment without changing the microphone
volume.
"FRONT"*/
Specify the voice output speaker.
"F-R"/ "F-L"
Output a beep from the speaker when a call comes in.
"ON"*/ "OFF"
Display the firmware version and update the firmware.
1 sec.
"OFF"/ "ON"*
Setting the operation check sound (beep sound) ON/
OFF.
Sets the clock.
1 sec.
"OFF"/ "ON"*
Turns off the display when no operation is performed.
"OFF"/
Dims the display part in conjunction with the light
"AUTO"*
switch of the vehicle.
"OFF"/ "ON"*
Sets whether the key illumination brightness is changed
in conjunction with the key operation.
"OFF"/ "ON"*
Specifies whether to display the red dotted line on the
display.
"OFF"/ "ON"*
Turns on/off the built-in amplifier.
*Factory setting
* Function of KDC-BT742U.
* Function of KDC-X493.
* Function of KDC-MP442U.
* iPod play mode cannot be set when
<iPodCTRL> is set to "OFF".
* Refer to <Menu Glossary> (page 38).
Condition Page
18
12
28
28
29
32
31
30,
31
17
30
*
28
*
*
*
*
*
30
19
*
*
Next page 3
7
|
English

Publicidad

Capítulos

Tabla de contenido
loading

Este manual también es adecuado para:

Kdc-x493Kdc-mp442u

Tabla de contenido