Thermal Protection - SPARKY BPR 15Li Instrucciones De Uso

the work area and improve visibility when operating in ar-
eas with insufficient light. To turn the LED light on press
the ON/OFF switch (3).
OPeRAtION mODe seleCtION
Select the operation mode by means of the switch (5).
WARNING: Switching between operation
modes shall be performed only if the power tool is
switched off!
"Hammer drilling" mode - hammer drilling in
concrete, stone, masonry, etc. (Fig.1a)
"Drilling" mode - drilling in metal, wood, plas-
tics, etc. (Fig.1b)
ReveRsING (Fig. 2)
WARNING: Reversing can be performed only
when the spindle is not rotating!
The extreme position of the lever (4) to the right is equiva-
lent to anti-clockwise rotation, the extreme position to the
left - to clockwise rotation.
When the ON/OFF switch (3) is depressed the lever (4)
can not be actuated.
Drilling and driving in screws is performed with the lever
(4) in its extreme position to the left. Loosening screws
and releasing a jammed drill bit is performed with the le-
ver (4) in its extreme position to the right.
PROteCtIve RING
The prevents penetration of dust generated during drill-
ing into the socket for the bit shank. (Fig. 3) Take care not
to damage the protective ring (7) while inserting the bit.
WARNING: A damaged protective ring it must
be immediately replaced in an authorised service cen-
tre.
INseRtING sDs-PlUs bIts
Clean and grease the shank of the accessory, before
placing it into the socket!
Pull the locking sleeve (6) backward (6). (Fig. 4)
Insert the bit untill stop. Ensure that the socket grooves
correspond to the shank channels, and then release the
sleeve to fix the bit.
Check the proper tightening of the bit attempting to pull
it near the sleeve.
To remove the bit, pull the sleeve (6) back, and then take
the bit out.
INseRtING stRAIGHt sHANK bIts
8
EN
WARNING: Do not ise tools without SDS-plus
shanks for hammer drilling! Otherwise the tool and the
chuck will be damaged.
mounting the keyless chuck
Clean and grease the SDS-plus shank of the chuck
adapter.
Pull the locking sleeve (6) backward. (Fig. 5)
Insert the adapter shank until stop. Ensure that the sock-
et grooves correspond to the adapter shank channels,
and then release the sleeve to fix the chuck with adapter
(16).
Check the proper tightening of the adapter attempting to
pull it near the sleeve.
To remove the chuck, pull the locking sleeve (6) back-
ward and take the chuck with adapter out.
Inserting a bit into the keyless chuck
Open the chuck (16) by rotating its front collar in the di-
rection of the symbol "RELEASE". (Fig. 6)
Insert the bit shank into the chuck.
Grip the rear collar of the chuck and rotate its front collar
in the direction of the symbol "GRIP".
Set the operation mode switch (5) to position for "Drill-
ing" mode.
To remove the bit, grip the rear chuck collar and rotate
its front collar in the direction of the symbol "RELEASE".
sWItCHING ON - sWItCHING Off
switching on: Press and hold the ON/OFF switch (3).
(Fig. 7)
switching off: Release the ON/OFF switch (3).
At low temperatures the power tool reaches its entire
hammer capacity only after a certain time.
The power tool is equipped with a brake. The spindle
stops rotating immediately after releasing the switch trig-
ger.
smOOtH eleCtRONIC RPm CONtROl
Light pressure on the ON/OFF trigger switch (3) results
in low rotation speed / low impact rate, further pressing
the switch results in smooth increase of the rpm to maxi-
mum upon reaching the extreme position. (Fig. 8)
bAtteRy stAte INDICAtION
▪ The LED indicator (9) shows the battery charge level
upon pressing the ON/OFF trigger switch (3) slightly
or to its extreme position. (Fig. 9)
▪ In case only 1 out of 3 LED glows on the indicator (9),
this means the battery has to be re-charged urgently
in order to gain its previous power.
Glowing LEDs
3
2
1

tHeRmAl PROteCtION

The power tool is not subject to overload when operated
Battery charge level
60% - 100%
20% - 60%
≤ 20%
BPR 15Li