Charging The Battery; Know Your Product; Operation - SPARKY BPR 15Li Instrucciones De Uso

▪ Do not incinerate the battery pack even if it is seriously
damaged or can no longer hold a charge. The battery
pack can explode in a fire.
▪ To facilitate the cooling of the battery pack after use,
avoid placing the charger or battery pack in a warm
environment such as in a metal shed, or an uninsu-
lated trailer.
WARNING: Never attempt to open the battery
pack for any reason. If the plastic housing of the bat-
tery pack breaks or cracks, return to a service centre
for recycling.
ReAD All Of tHe INstRUCtIONs IN tHe CHARG-
eR seCtION Of tHIs mANUAl befORe AttemPt-
ING tO CHARGe tHe bAtteRy PACK fOR yOUR
tOOl.
▪ Always use correct SPARKY battery pack (the one
supplied with tool or a replacement pack exactly like
it.) Never install any other battery pack. It will ruin
your tool and may create a hazardous condition.
▪ Charge battery packs only in SPARKY chargers.
▪ Use an environmentally safe disposal unit at a munici-
pal waste disposal centre to dispose of a damaged or
worn out battery.
fIttING AND RemOvING tHe bAtteRy PACK
to remove the battery: Press simultaneously the re-
lease tabs no both sides of the battery, and pull it down-
ward and out of the machine.
Prior to inserting the battery ensure that the switch is in
OFF position.
to install the battery: Insert the charged battery into
the slot until the battery is securely latched with a click.

CHARGING tHe bAtteRy

▪ The battery for this power tool is shipped partially
charged. You should charge the battery fully before
using the power tool for the first time.
▪ Li-Ion battery is protected against deep discharging.
When the battery is empty, the machine is automati-
cally switched off.
WARNING: Do not continue to press the ON/
OFF switch (3) after the machine has been automati-
cally switched off. This may damage the battery.
The battery is equipped with a temperature control,
which allows charging only within the temperature range
from 0 °C to approx. 45 °C. A longer battery service life
is achieved in this manner.
1. Insert the charger plug (14) into the mains supply
socket. The LED indicator (15) starts to glow signify-
ing the presence of supply voltage.
2. Insert the charger jack (13) into the socket (10) on
the back lower part of the handle. The green LED
indicator (11) starts to blink, signifying that charg-
ing process has begun. Charging the battery takes
about 1 hour. The battery is fully charged when the
Original instructions
indicator (11) starts to glow continuously.
3. Take the charger plug out of the mains socket.
4. Take the charger jack out of its socket on the power
tool handle.
WARNING: Do not operate the power tool
while the battery is charging.
tO ObtAIN tHe best lIfe fOR tHe bAtteRy
▪ When battery is not in use, keep it away from other
metal objects like paper clips, coins, keys, nails,
screws, or other small metal objects that can make
a connection from one terminal to another. Shorting
the battery terminals together may cause fire or ex-
plosion.
▪ Always unplug the charger when not in use and store
in a dry secure place.
▪ Do not charge batteries and do not store the charger
in premises where the temperature may drop under
0ºC or exceed 40°C.
▪ Each new battery reaches its full loading capacity af-
ter several charge-discharge cycles (4-5). If the bat-
tery has not been used for some time, it is better to
recharge it before use.
VII - Know your product
Before using the power tool, familiarize yourself with all
operating features and safety requirements.
Use the tool and accessories only for the applications
intended. All other applications are expressly ruled out.
1. Handle
2. Rechargeable battery pack
3. ON/OFF trigger switch
4. Forward/reverse switch
5. Operation mode switch
6. SDS-plus locking sleeve
7. Protective ring
8. LED work area light
9. Battery charge LED indicator
10. Socket for connecting the battery to the charger
11. Charger LED indicator
12. Charger
13. Jack for connecting the charger to the battery
14. Plug for connecting the charger to the mains supply
15. Mains LED indicator
16. Keyless chuck with SDS-plus adapter
17. SDS-plus to ¼" hex adapter
VIII - Operation
This power tool is designed for hammer drilling in con-
crete, stone, masonry and various brittle materials. The
rotary hammer can be used for drilling in steel, wood,
plastics, etc. by means of the keyless chuck with adapter.
leD WORK AReA lIGHt
The machine is equipped with LED light (8) to illuminate
7
EN