Miche REVOX Manual De Uso página 6

Rear Hub
Front hub
The REVOX RC hubs are easy to maintain. To do it, proceed as
follows:
Front hub
Insert two keys (A) in the extremity of the hubs (Pic. 1), and turn
them in anti-clock sense.
While you are taking out the mobile side, take out from the opposite
side the complete pin.
• Once you take out the pin from hub's body, you could, if it is
necessary, change the bearings.
To reassembly it:
• Put the pin into the hub's body and lock with power the mobile
side with a torque of 15 Nm. If necessary, adjust the hub by
working on the ring (D):
• Unlock the grub screw (E) with a key (B) (Pic. 1).
• Turn the ring clockwise to drop the sliding, and anti-clockwise to
raise the sliding. Lock the grub screw (E).
Check the sliding of the wheel.
Please check that the hub is correctly tightened and closed, failure
to do so could lead to a serious or fatal accident.
Warning
Use original spare parts exclusively provided by Fac
Michelin Srl. Any modification or alteration (also graphic)
of the product with non-original spare parts or spare
parts not delivered directly by Fac Michelin Srl, involves
the expiration of the guarantee.
Rear hub
Insert two keys (A) in the extremity of the hubs (Pic. 2), and turn
them in clock sense.
• Once you take out the pin from hub's body, the free wheel body
(C) stays attached with his pawls (Pic. 2).
• Clean carefully the pawls then put some low-density grease.
• Re-fit the pin (C) inside hub body with the spacer (Z) (Pic. 2).
• Take care to position of the pawls positions. Lock with power the
mobile side with a torque of 15 Nm (Pic. 3), if necessary adjust the
hub by working on the ring (D):
• Unlock the grub screw (E) with a key (B) (Pic. 3).
• Turn the ring in clock sense to drop the sliding, and in anti-clock
sense to rise the sliding. Lock the grub screw (E).
Check the sliding of the wheel.
Please check that the hub is correctly tightened and closed, failure
to do so could lead to a serious or fatal accident.
Warning
Use original spare parts exclusively provided by Fac Use
original spare parts exclusively provided by Fac Michelin
Srl. Any modification or alteration (also graphic) of the
product with non-original spare parts or spare parts
not delivered directly by Fac Michelin Srl, involves the
expiration of the guarantee.
SECTION III:
Spokes manteinance
When replacing any broken spokes please ensure spokes of the
correct length and specification are used.
Rear whee
Right side
Left side
Right side 28x15x7 (6902)
Left side 24x12x6 (6901)
Free wheel 24x12x6 (6901)
24x12x6 (6901)
277 mm
277 mm
Front wheel
Right side
Left side
CHANGE A SPOKE
Warning
If you have any doubt whatsoever your service-repair
ability, please take your bicycle to a qualified repair
shop.
Before any maintenance operations on your wheels,
always wear gloves and protection glasses.
Use only spokes of the same length and characteristics
of those being replaced.
Use original spare parts exclusively provided by Fac
Michelin S.r.l.
Front hub
• Insert two keys (A) in the extremity of the hubs. Turn them in
anti-clock sense.
• Once you take out the mobile side, if it is necessary take out the
complete pin from the opposite side.
Take out the damaged spoke, then put in the new spoke Pic.4.
• If it is necessary put the pin into hub's body, and lock with power
the mobile side with a torque of 15 Nm.
Check the sliding of the wheel.
Please check that the hub is correctly tightened and
closed, failure to do so could lead to a serious or fatal
accident.
Rear hub
To change a spoke on the left side of the hub:
• Insert two keys (A) inside the extremity of the hub and turn them
in clock sense.
• Once you take out the mobile side, take out the damaged spoke,
then put in the new spoke (Pic.5).
• Lock with power the mobile side with a torque of 15 Nm.
Check the sliding of the wheel.
Please check that the hub is correctly tightened and
closed, failure to do so could lead to a serious or fatal
accident.
To change the spokes on the free wheel side of the hub, it is no
necessary to take out the pin from hub's body.
To ensure the optimum wheel "dish" spoke line, please follow the
indications below:
• Correct spoke tension for front wheel: 1100/1200 N.
• Correct spoke tension for rear wheel, free wheel side: 1400 N.
To evaluate the correct wheel tension, please use a professional
spoke tension gauge, we do not recommend that spoke tension is
estimated manually; please refer to a professional cycle mechanic
if you do not own a professional spoke tension gauge. The
correct spoke tension is essential to ensure a ridged and durable
wheelset.
ATTENTION in correct spoke tension, too high or too low,
could lead to wheel failure and resulting serious or fatal
accident.
When replacing spokes please ensure thread lock compound is
used.
SECTION IV:
Complete wheels
REVOX RC wheels are developed to set up clincher tyre.
Miche wheels are designs for use solely on the road or dedicated
cycle track with a smooth surface. Please ensure that the wheels
are not subject to direct shock from poor road surfaces [i.e. pot
6
276 mm
276 mm