DSC Power Serie Manual Del Usuario página 33

FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by
Digital Security Controls could void your authority to use this equi-
pment.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interfer-ence in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be deter-mined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Re-orient the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician
for help.
The user may find the following booklet prepared by the FCC useful:
"How to Identify and Resolve Radio/Television Interference
Problems". This booklet is available from the U.S. Government
Printing Office, Washington D.C. 20402, Stock # 004-000-00345-4.
The keypads represented in this manual can be used with the following
Control Unit: PC1404.
IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC Rules and, if the
product was approved July 23, 2001 or later, the requirements
adopted by the ACTA. On the side of this equipment is a label that
contains, among other information, a product identifier. If requested,
this number must be provided to the Telephone Company.
PC1404 Product Identifier
USOC Jack: RJ-31X
Telephone Connection Requirements
A plug and jack used to connect this equipment to the premises wiring
and telephone network must comply with the applicable FCC Part 68
rules and requirements adopted by the ACTA. A compliant telephone
cord and modular plug is provided with this product. It is designed to
be connected to a compatible modular jack that is also compliant. See
installation instructions for details.
Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be
connected to a telephone line. Excessive RENs on a telephone line
may result in the devices not ringing in response to an incoming call.
In most but not all areas, the sum of RENs should not exceed five
(5.0). To be certain of the number of devices that may be connected
to a line, as determined by the total RENs, contact the local
Telephone Company. For products approved after July 23, 2001, the
REN for this product is part of the product identifier that has the
format US: AAAEQ##TXXXX. The digits represented by ## are the
REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier
products, the REN is separately shown on the label.
Incidence of Harm
If this equipment (PC1404) causes harm to the telephone network, the
telephone company will notify you in advance that temporary
discontinuance of service may be required. But if advance notice is not
practical, the Telephone Company will notify the customer as soon as
possible. Also, you will be advised of your right to file a complaint with
the FCC if you believe it is necessary.
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities,
equipment, operations or procedures that could affect the operation of
the equipment. If this happens the Telephone Company will provide
advance notice in order for you to make necessary modifications to
maintain uninterrupted service.
Equipment Maintenance Facility
If trouble is experienced with this equipment (PC1404) for repair or
warranty information, contact the facility indicated below. If the
equipment is causing harm to the telephone network, the Telephone
Company may request that you disconnect the equipment until the
problem is solved. This equipment is of a type that is not intended to be
repaired by the end user.
DSC c/o APL Logistics 757 Douglas Hill Rd, Lithia Springs, GA
30122
US: F53AL01BPC1404
Additional Information
Connection to party line service is subject to state tariffs. Contact the
state public utility commission, public service commission or
corporation commission for information. Alarm dialing equipment
must be able to seize the telephone line and place a call in an emergency
situation. It must be able to do this even if other equipment (telephone,
answering system, computer modem, etc.) already has the telephone
line in use. To do so, alarm dialing equipment must be connected to a
properly installed RJ-31X jack that is electrically in series with and
ahead of all other equipment attached to the same telephone line.
Proper installation is depicted in the figure below. If you have any
questions concerning these instructions, you should consult your
telephone company or a qualified installer about installing the RJ-31X
jack and alarm dialing equipment for you.
INDUSTRY CANADA STATEMENT
NOTICE: This Equipment meets the applicable Industry Canada
Terminal Equipment Technical Specifications.
Le présent materiel est conforme aux specifications techniques
applicables d'Industrie Canada.
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1.
L'indice d'équivalence de la sonnerie (IES) du présent matériel est de 0.1.
The Ringer Equivalence Number is an indication of the maximum number of de-
vices allowed to be connected to a telephone interface. The termination on an in-
terface may consist of any combination of devices subject only to the
requirement that the sum of the RENs of all the devices does not exceed five.
L'indice d'équivalence de la sonnerie (IES) sert à indiquer le nombre maximal
de terminaux qui peuvent être raccordés à une interface téléphonique. La termi-
naison d'une interface peut consister en une combinaison quelconque de dispo-
sitifs, à la seule condition que la somme d'indices d'équivalence de la sonnerie
de tous les dispositifs n'excède pas 5.
The term 'IC:' before the radio certification number only signifies that Industry
Canada technical specifications were met.
Certification number IC: 160A-PC1404
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003
du Canada.