Know Your Product; Operation; Prior To Initial Operation; Replacing The Blade - SPARKY Professional TK 40 Instrucciones De Uso

regulations in force in your area. The same applies for
general rules of occupational health and safety.
▪ The manufacturer shall not be liable for any changes
made to the tool nor for any damage resulting from
such changes.
▪ Power tools must not be used outdoors in rainy weath-
er, or in moist environment (after rain) or in close vicin-
ity with easily flammable liquids and gases. The work-
ing place should be well lit.

Know your product

Before using the power tool, familiarize yourself with all
the operating features and safety requirements.
Use the tool and accessories only for the applications
intended. All other applications are expressly ruled out.
1. Blade
2. Riving knife
3. Outer blade flange
3a. Inner blade flange (not shown)
4. Blade bolt
5. Base plate
6. Upper immobile blade guard
7. Dust extraction port
8. Back handle
9. ON/OFF switch
10. Motor
11. Front handle
12. Blade guard lever
13. Depth adjustment scale
14. Depth adjustment lever
15. Rip fence
16. Depth adjustment fixing
17. Rip fence lock knob
18. Cutting guide notch 45º
19. Cutting guide notch 90º
20. Mobile blade guard
21. Spindle lock button
22. Lock-off button
23. Bevel scale
24. Bevel adjustment fixing
25. Bevel adjustment lever

Operation

This power tool is supplied from single-phase alternat-
ing current mains only. It is double insulated according
to EN 60745-1 and IEC 60745 and can be connected
to grounded or not grounded sockets. This power tool
is radio suppressed in compliance with EMC Directive
2004/108/EC.
This power tool is designed for longitudinal and cross saw-
ing wood in a straight line at bevel angle from 0° to 45°.

PRIOR TO INITIAL OPERATION

WARNING: Always switch off and unplug the
power tool prior to any adjustment, servicing or mainte-
nance or in case of mains drop-out.
Original instructions
▪ Make sure the power supply voltage corresponds to
the value indicated on the name plate with technical
data of the tool.
▪ Always check the position of ON/OFF switch. The
power tool must be connected to the power supply
socket only when this switch is in OFF position. If the
plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
▪ Make sure that the cord and the plug are in order. If the
replacement of the supply cord is necessary, this has
to be done by the manufacturer or his agent in order
to avoid a safety hazard.
▪ Always inspect the blade. Use only well grinded
blades. Never use blades with cracks and indents or
HSS-blades.
▪ Check if the blade is tightened reliably and moves
freely.
▪ Check if the mobile guard moves freely.
▪ Make sure the work piece or the material is well se-
cured.
▪ Let the machine operate at no load for 30 seconds.
Replace the blade in case vibrations are observed.

REPLACING THE BLADE

WARNING: Unplug the power tool!
1. Press the spindle lock button (21).
Whilst depressing the spindle lock button (21) using
the blade spanner delivered with the machine, turn
bolt (4) anti-clockwise.
Remove the blade bolt (4) and the outer blade flange
(3). (Fig. 1)
2. Ensure blade flanges and bolt is clean of sawdust,
grease, etc.
3. Move the lower blade lever (12) anti-clockwise, to lift
the lower guard (20) toward the upper blade guard
(6). While performing this step check the proper func-
tioning of the lower guard spring. (Fig. 2)
4. Make sure the blade teeth and arrow on the blade (1)
point in the same direction as the arrow on the upper
blade guard (6).
5. Slide the new blade (1) through slot in the base plate
(5) and mount it against the inner blade flange (3a) on
the shaft. Make sure the large diameter of the blade
flanges lay flush against the blade (1).
6. Tighten the outer blade flange (3).
First tighten blade bolt (4) to finger tight. Engage
spindle lock button (21).
Whilst depressing the spindle lock button (21), tight-
en blade bolt (4) firmly with the blade spanner sup-
plied with the machine.
7. Before connecting the saw to a power source, en-
sure that:
- The spindle lock button (21) is released;
- The blade (1) rotates freely;
- The lower blade guard (20) operates correctly.
NOTE: Do not modify the blade spanner to elongate it,
since it may lead to over tightening of the blade bolt (4).
After each replacement of the blade check the distance
7
EN