Mitsubishi Electric City Multi PLFY-WP-VBM-E Serie Manual De Instrucciones página 7

3. Operation
<Exiting the Main menu screen>
Fri
Room
Cool Set temp. Auto
Mode Temp. Fan
F1 F2 F3 F4
If no buttons are touched for 10 minutes, the screen will automatically
return to the Main display. Any settings that have not been saved will
be lost.
<Display of unsupported functions>
Title
Not available
Unsupported function
Return:
F1 F2 F3 F4
3.5.2 Vane·Vent. (Lossnay)
<Accessing the menu>
Main Main menu
Vane·Louver·Vent. (Lossnay)
High power
Timer
Weekly timer
OU silent mode
Main display:
Cursor Page
F1 F2 F3 F4
<Vane setting>
Fri
Swing Off Off
Vane Vent. Louver
F1 F2 F3 F4
Fri
Room
Cool Set temp. Auto
Mode Temp. Fan
Press the [RETURN] button to exit
the Main menu and return to the
Main display.
The message at left will appear if
the user selects a function not sup-
ported by the corresponding indoor
unit model.
Select "Vane·Louver·Vent. (Loss-
nay)" from the Main menu (refer to
page 6), and press the [SELECT]
button.
Press the [F1] or [F2] button to go
through the vane setting options:
"Auto", "Step 1", "Step 2", "Step 3",
"Step 4", "Step 5" and "Swing".
Select the desired setting.
Auto
Auto Step 1 Step 2
Step 3 Step 4 Step 5
Swing
Swing
Select "Swing" to move the vanes
up and down automatically.
When set to "Step 1" through "Step
lected angle.
under the vane setting icon
This icon will appear when the
vane is set to "Step 5" and the
fan operates at low speed during
cooling or dry operation (depends
on the model).
The icon will go off in an hour, and
the vane setting will automatically
change.
<Vent. setting>
Low
Vent.
F1 F2 F3 F4
<Returning to the Main menu>
Main Main menu
Vane·Louver·Vent. (Lossnay)
High power
Timer
Weekly timer
OU silent mode
Main display:
Cursor Page
F1 F2 F3 F4
Note:
During swing operation, the directional indication on the screen
does not change in sync with the directional vanes on the unit.
Available directions depend on the type of unit connected.
In the following cases, the actual air direction will differ from the
direction indicated on the remote controller display.
2. Immediately after starting heat mode (while the system is wait-
ing for the mode change to take effect).
3. In heat mode, when room temperature is higher than the tem-
perature setting.
wired remote controller) >
Note:
This function cannot be set depending on the outdoor unit to be
connected.
DOWN air direction setting of remote controller.)
Manual vane angle
Main Main menu
Maintenance
Initial setting
Service
Main display:
Cursor Page
F1 F2 F3 F4
Maintenance menu
-
Auto descending panel
Manual vane angle
Main menu:
Cursor
F1 F2 F3 F4
Press the [F3] button to go through
Fri
the ventilation setting options in the
order of "Off", "Low", and "High".
* Settable only when LOSSNAY unit
is connected.
Off Low
Off Low
units may be interlocked with cer-
tain models of ventilation units.
Press the [RETURN] button to go
back to the Main menu.
1 Select "Maintenance" from the
Main menu (refer to page 6), and
press the [SELECT] button.
2 Select "Manual vane angle" with
the [F1] or [F2] button, and press
the [SELECT] button.
High
High
7