Press the ▲▼ keys to confirm / cancel tab pre-
infusion.
Press the RESET key to quit the submenu and
return to the main menu, confirming the setting.
Press the ENTER key to scroll through each
single item in the submenu and confirm the set-
tings.
12. TAMPING
Press the ENTER key to access the sub-
menu.
This allows you to program the coffee
tamping for each drink (YES or NO).
1 Tamping Ristretto
2 Tamping 2 Ristretto
3 Tamping Espresso
4 Tamping 2 Espresso
5 Tamping Coffee
6 Tamping 2 Coffee
7 Tamping CoffeeCreme
8 Tamping caffellatte
9 Tamping Macchiato
10 Tamping Cappuccino
11 Tamping Big Cappuccino
The arrow keys ▲▼ confirm/disconfirm the
tamping function for each drink.
Press the RESET key to exit the submenu and
go back to the main menu and to confirm the
tamping programmed.
Press the ENTER key to scroll all the items on
the submenu and see confirmation of the tamp-
ing programmed.
13. GROUNDS NUMBER
Press the ENTER key to access the sub-
menu.
This allows you to program the
GROUNDS NUMBER. When the number
has been reached, a message will be dis-
played instructing you to empty the coffee
grounds drawer and the machine will stop
56
working to allow the procedure to be done
safely.
The arrow keys ▲▼ increase/decrease the
grounds number to proceed to the emptying of
the coffee grounds drawer.
Press the RESET key to exit the submenu and
go back to the main menu and to confirm the
grounds number programmed.
The ENTER key is disabled.
14. MILK CLEAN WARN. H
Press the ENTER key to access the sub-
menu.
This allows you to program after how
many hours, following the last milk deliv-
ery, the milk foamer cleaning warning will
be displayed.
The arrow keys ▲▼ increase/decrease the
amount of hours for the display of the milk
foamer cleaning warning message.
Press the RESET key to exit the submenu and
go back to the main menu and to confirm the
number of hours programmed.
The ENTER key is disabled.
15. CLEAN WARNING
Press the ENTER key to access the sub-
menu.
This allows you to program the number of
cycles after which the group clean warn-
ing will be displayed.
The arrow keys ▲▼ increase/decrease the
amount of hours for the display of the group
clean warning message.
Press the RESET key to exit the submenu and
go back to the main menu and to confirm the
number of cycles programmed.
The ENTER key is disabled.
16. FINAL WASHING CYCLE
Press the ENTER key to access the sub-
menu.
This programmes a cleaning cycle for the
dispenser group when the machine is
switched off.
Set to YES to enable this function.
If the function is enabled, 100 cm
cu in) of water will be dispensed
Press the ▲▼ keys to enable (YES) / deacti-
vate (NO) cleaning at the end of service.
17. GROUP SETTING
Press the ENTER key to access the sub-
menu.
This allows you to program the group
repositioning.
The arrow keys ▲▼ increase/decrease the
riascent of the motor.
Press the RESET key to exit the submenu and
go back to the main menu and to confirm the
programming.
The ENTER key is disabled.
18. GRINDER SETTING
Press the ENTER key to access the sub-
menu.
This allow you to program the choice of
increasing grinding times by o.5 seconds
every 50-250 deliveries.
By setting the program at 0, the function is
disabled
The arrow keys ▲▼ increase/decrease the
number of deliveries, after which there will be
an increase in grinding time.
The available values are 0, 50,100, 150, 200,
250.
Press the RESET key to exit the submenu and
3
(6.1024