Topcom DIABLO 100 Manual De Usuario página 3

1 Buttons (see folding page for the picture)
1. Numerical buttons
2. Off -hook button
3. Redial / Pause button
4. Flash R/ INT
5. Direct memory button M1
6. Paging button (to retrieve the handset)
7. Mute button
2 Display
You are online
INT = Internal communication
EXT = External communication
New numbers in call list
The keypad is locked
The antenna indicates the quality of reception
The antenna blinks when the handset is out of range!
Memory records are being retrieved or set up
3 Installation (See picture on folding page)
4 Battery low indication
When the battery is empty, the handset no longer carries out operations.
Full battery
When you are in the middle of a conversation and the battery is almost empty, the handset will emit a warning signal. Place the handset
on the base unit to charge.
5 Operation
5.1 Outgoing calls
5.1.1 Making a phone call or redialing one of the last 5 numbers
Enter the desired telephone number or press the Redial key
few times until the desired number appears on the display
when you want to terminate the call.
Note: Press the Mute button
Note: You can set the volume between 1-5 by pressing the scroll button
5.1.2 Call setup with dial preparation
Enter the desired telephone number. An incorrect number can be corrected by means of the Mute
. The number will be dialled automatically.
5.2 Incoming calls
When a call comes in, the handset will start to ring.
the On-hook button .
5.3 Programming memory numbers
You can program 10 indirect numbers (of max. 24 digits) in the phone's memory.
Press the Memory button short. The first entry will be shown on the display
icon appears on the display.
number you whish to store.
appear. To leave the memory programming, press the on-hook
Note: If you wish to insert a pause, press the Redial/Pause button
5.4 Calling a memory number
Press the Memory button
. The memory number will be dialled automatically.
5.5 Direct access memory (Key 1,2,3 and M1)
The product has 3 locations (Key '1', '2' and '3') where you can store a number under and dial it by pressing and holding one of these keys
in standby. The phone will automatically take the line and dial the number which is stored under this key. The number stored under key
'1' can also be dialed out by pressing the 'M1'-key shortly in standby.
5.5.1 Programing the direct memory keys
Press the Memory button short. Press and hold the Memory button
of the 3 direct memory keys (Key 1,2 or 3) where you want to store the number under until 'Sx - _' appears.
you whish to store. Press the Memory button
To leave the direct memory programming, press the On-hook button
5.6 Paging
Press the Paging button
ringing on all handsets.
5.7 Programming procedure
You can change the ring melodie, volume, day, time etc... by going into the program procedure: To go into the program procedure you
have to press and hold the Program button
setting. Each time you press the Program button
Topcom Diablo 100/Twin/Triple/Quattro
/P
Empty battery
during a conversation. to deactivate or activate the microphone.
Press the On-hook button
Enter the location (0-9) where you want to store the telephone number under.
Press the Memory button
Scroll with the Up/Down keys
again to confirm.
on the base unit, the handset emits a ringing signal to help you find a lost handset. Press any key to stop the
until the icon
you will confirm the previous setting and jump to the next setting:
ENGLISH
8. On hook button
9. Charge indicator/ On line (LED)
10. Call log/Scroll Up
11. Scroll Down
12. Key lock
13. Program/Memory button
- x -
/
hh:mm
to dial out one of the last 5 numbers
Press the Off-hook button
Press the Off-hook button
again to confirm. You will hear a confirmation tone and the next entry will
button.
on the location where you want a pause of 3 sec.
/P
to the entry you want to dial (0-9).
Press the On-hook button
until the
You will hear a confirmation tone and the next entry will appear.
.
starts to flash.
/
/
There are more digits on the left
There are more digits on the right
Program mode
x = handset number
Answered/Unanswered calls
Time: hh = hours, mm = minutes
press the scroll keys
to dial out Press the on-hook button
.
button.
when you want to terminate the call.
to answer the incoming call. To end the call press
Press and hold the Memory button
to terminate the call.
-icon appears on the display. Press and hold one
Enter the telephone number
Press the Program button again to change the first
a
Press the Off-hook button
until the -
Enter the telephone
Press the Off-hook button
3