Metabo BS 18 LTX BL Impuls Instrucciones De Manejo página 9

Ocultar thumbs Ver también para BS 18 LTX BL Impuls:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

5. Figures
Illustrations are provided at the beginning of the
operating instructions.
Symbol explanation:
Movement direction
Slow
Fast
First gear
Second gear
Screws
Drill bit
Without torque limitation
Impact drilling
Torque
Nm
6. Overview
Fig. A
1 Keyless chuck
2 Additional handle
3 Slide switch (normal drilling, impact drilling) *
4 Slide switch (1st/2nd gear)
5 Button (switch between 'max. torque' and function
set at setting wheel (13)) *
6 Rotation selector switch (rotation setting,
transport lock) - both sides of the machine
7 Bit depot *
8 Belt hook *
9 Battery pack release button
10 Capacity indicator button
11 Capacity and signal indicator
12 Battery pack
13 Setting wheel (pulse function, torque control,
where applicable 'max. torque') *
14 LED lights
15 Trigger switch
*equipment-specific
7. Use
7.1
Battery pack, capacity and signal display
Fig. B
Charge the battery pack before use.
If performance diminishes, recharge the battery
pack.
The ideal storage temperature is between 10 °C
and 30 °C.
7.2
Removing, replacing battery pack
Fig. C
7.3
Setting direction of rotation, transporting
safety device (switch-on lock)
7.4
Selecting gear stage
Only actuate slide switch (4) with the motor at
a standstill!
7.5
Setting for normal drilling, impact drilling
Fig. A
Press the slide switch (3).
7.6
Setting torque control, maximum torque,
pulse function
Do not work for long periods with pulse func-
tion switched on! (The motor can overheat.)
Machines with designation ...18 LTX BL Quick...:
Fig. F
Turn the setting wheel (13) to switch on the pulse
function (button (5) flashes) or to switch on the
torque control (button (5) lights up continuously)
For maximum torque (drilling position), press the
button (5) (the button (5) is not illuminated). To acti-
vate the settings of setting wheel again: press the
button (5) again or turn the setting wheel.
Machines with designation ...18 LTX Impuls/
Quick, ...18 LTX BL Impuls:
Set the desired operating mode at the setting wheel
(13):
1...10 =
Drill bit =
Impuls =
7.7
Switching on/off, setting speed
Fig. A
Switching on, speed: Press the trigger (15). The
speed can be changed by pressing in the
trigger.
Switching off: release the trigger switch (15). Note:
The noise that the machine makes when it
switches off is due to the design (quick stop)
and has no influence on the function or the
service life of the machine.
7.8
Keyless chuck
With a soft tool shank, retightening may be required
after a short period of operation.
Notes on machines with the designation SB...:
1. The ratchet sound which can possibly be heard
after opening the drill chuck is functional and is
switched off by a reverse rotation of the sleeve.
2. Clamping tool:
Turn sleeve (1) in direction "GRIP, ZU" until the
noticeable mechanical resistance has been
overcome.
Caution! The chuck is not yet fully tight-
ened! Keep turning the sleeve (it must "click"
when turning)) until it cannot be turned any
further - only now is the tool safely clamped.
Cleaning: From time to time, hold the machine
vertically with the keyless chuck facing
downwards and turn the sleeve fully in direction
"GRIP, ZU" and then turn fully in direction
Fig. D
torque control
maximum torque
pulse function
Fig. H
ENGLISH en
Fig. E
Fig. G
9

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Bs 18 ltx bl quickBs 18 ltx impulsBs 18 ltx quickSb 18 ltx bl impulsSb 18 ltx bl quickSb 18 ltx impuls ... Mostrar todo

Tabla de contenido