Translation of the Original Operation Manual
GB
Übersetzung der Originalbetriebsanleitung
MATERIAL JAM IN THE MACHINE:
(Auto-reverse function)
If a jam is caused by feeding in too much material, the
machine reacts as follows:
- The cutting mechanism is blocked, then runs briefl y
in reverse (material is released) and stops. The
motor is switched off.
- The control display
(6) lights up.
Proceed as follows:
Paper jam in paper feed slot (12)
- Remove released paper from the feed slot (12).
- Cutting mechanism now runs forwards automatically
and shreds the remaining paper in the cutting
mechanism.
- The control display
(6) goes out. The LED display
of the forwards button (3) is permanently lit.
- Continue shredding with lower quantity of paper.
Material jam in safety feed slot (13)
- Remove released material.
Take care when removing material as
sharp edges may cause injury!
CLEANING THE PHOTOCELLS (Fig. 5):
If paper particles should come to rest in the inlet
guide (for example after a paper jam) it is possible
that the machine will not turn off, due to the broken
light barrier.
To remove these paper strips and also to clean the
photocell, pass another sheet of paper through the
feed slot, or switch the machine to reverse and wipe
both "eyes" of the photocell with a brush.
fi g. 5
Model
Typ
intimus 26SC2
276-4S
intimus 26CC3
276-4C
intimus 32SC2
277-4S
intimus 32CC3
277-4C
Pre-fusing (slow-blow):
220-240V = 10 amps / 120V = 15 amps
Model
intimus 26SC2
220-240V/50Hz · 1.7 amps · 0.40 kW 120V/60Hz · 2.9 amps · 0.31 kW
intimus 26CC3
220-240V/50Hz · 1.7 amps · 0.40 kW 120V/60Hz · 2.9 amps · 0.31 kW
intimus 32SC2
220-240V/50Hz · 1.9 amps · 0.44 kW 120V/60Hz · 3.5 amps · 0.39 kW
intimus 32CC3
220-240V/50Hz · 1.9 amps · 0.44 kW 120V/60Hz · 3.5 amps · 0.39 kW
MALFUNCTIONS
- The remaining material is now automatically fed into
the cutting mechanism again and shredded.
- The control display
of the forwards button (3) is permanently lit.
- When the material has run through, continue
shredding with correct quantities.
- If necessary, operate the cutting mechanism manually
forwards and backwards alternately until the material
has completely run through and has been shredded.
Wait each time until the motor stops
before switching direction!
MOTOR PROTECTION:
If the motor is overloaded, it switches off. The control
display
(9) fl ashes.
After a cooling down period of approx. 25-40 minutes
(depending on the model and room temperature), you
can switch the machine on again.
MAINTENANCE / DISPOSING
MAINTENANCE OF THE
CUTTING MECHANISM (CROSS-CUT):
Cross-cut cutting mechanisms must be oiled
after a certain operating time.
If the control display
as follows:
Pull out receptacle (14), take oil receptacle (16) (Fig.
6) out of the holder in the lower cabinet and push
receptacle in again.
Spread some oil on a sheet of paper and then feed
it into the cutting mechanism through the paper feed
slot (12).
The paper is drawn in and the oil thus gets into the
cutting mechanism.
Note: The oiling procedure needs to be confi rmed as
16
follows to delete the control display:
- Pull out receptacle (14) until the control display
(8) lights up.
- The control displays
- Press backwards button (4) and keep pressed until
the control display
fi g. 6
- Push receptacle in again.
TECHNICAL DATA
Cutting width
Cutting capacity
paper / CD,DVD
paper / CD,DVD
4 mm / 8 mm
13 sheets* / 1 piece
4x28 mm / 8 mm
9 sheets* / 1 piece
4 mm / 8 mm
17 sheets* / 1 piece
4x28 mm / 8 mm
12 sheets* / 1 piece
Power supply data
supply voltage/frequency · current consumption · power
(6) goes out. The LED display
(7) lights up, proceed
(7) and
(4) fl ash.
(7) goes out.
Working width
Noise level
240 mm
app. 55 dB(A)
240 mm
app. 55 dB(A)
240 mm
app. 55 dB(A)
240 mm
app. 55 dB(A)
7
CHECKLIST IN THE EVENT OF FAULTS:
If the machine does not work, check the following
points:
- is the mains plug connected to the mains?
- is the machine in "Sleep" mode?
See "AUTOMATIC ENERGY SAVING".
- has the user interlock been activated?
See "OPERATION OF THE USER INTERLOCK".
- is the receptacle pushed in?
- is the receptacle full?
Follow the instructions in "EMPTYING THE
RECEPTACLE".
- is there a material jam in the machine?
Follow the instructions in "MATERIAL JAM IN THE
MACHINE".
- Has the motor been overloaded?
See "MOTOR PROTECTION".
If none of the above applies, please contact your
dealer.
The cutting mechanism now automatically begins
the cleaning cycle (forwards operation/backwards
operation) and then switches off. The machine is
ready again. To re-order the special oil, see "SPECIAL
ACCESSORIES".
AUTOMATIC ENERGY-SAVING:
If the machine is not used for a while, it automatically
switches to the so-called "Sleep" mode after approx.
30 mins. The LED display
of the function button
(2) for "Ready" goes out. To switch on again, briefl y
press the function button. If the user interlock is
switched on, it must be deactivated again when the
machine is switched on again (see "OPERATING THE
MACHINE").
DISPOSING OF THE MACHINE:
Dispose of the machine in an environmentally
friendly fashion at the end of its useful service
life. Do not dispose of any of the parts
included in the machine or its packaging with
household waste.
Intermittent operation
Dimensions
ON / OFF
W x D x H
10 / 45 min
390 x 330 x 550 mm
10 / 45 min
390 x 330 x 550 mm
10 / 45 min
390 x 360 x 600 mm
10 / 45 min
390 x 360 x 600 mm
* based on A4-paper 70g/m² at 230V/50Hz – 10%
SPECIAL ACCESSORIES
Description
Plastic bag, 300x300x700x0.018 mm
Lubricant, 110 ml bottle
Note: For orders of special accessories and spare parts,
please contact your dealer.
Weight
16 kg
16.2 kg
16.5 kg
16.7 kg
Order-No.
99925
88035