Electrical Connection - Speck BADU 93 Manual De Uso

Installation
5.4

Electrical connection

Pos: 102 /Technische Dokumentation/Betriebsanleitung/Installation/Elektrischer Anschluss/Warnung Stromschlaggefahr @ 7\mod_1472027138452_370.docx @ 94227 @ @ 1
WARNING
Risk of electric shock due to incorrect connections!
 Electrical connections must always be carried out by
authorised specialists.
 Observe VDE and utility company regulations.
 Install swimming pools and their protection according to
DIN VDE 0100-702.
Pos: 103 /Technische Dokumentation/Betriebsanleitung/Installation/Elektrischer Anschluss/Trennvorrichtung zur Unterbrechung @ 7\mod_1472028985822_370.docx @ 94296 @ @ 1
 Install a disconnecting device with at least a 3 mm contact
gap per pole to interrupt the power supply.
Pos: 104 /Technische Dokumentation/Betriebsanleitung/Installation/Elektrischer Anschluss/Warnung Stromschlaggefahr; Dreh- oder Wechselstrom ohne Motorschutz (PDB) @ 7\mod_1472040457710_370.docx @ 94458 @ @ 1
WARNING
Risk of electric shock due to voltage on the housing!
 A built-in or external overload switch which is set correctly
must be installed for pumps with three-phase or A.C. motors
without motor protection (see pump data sheet). In doing so,
observe the values on the motor name plate.
Pos: 105 /Technische Dokumentation/Betriebsanleitung/Installation/Elektrischer Anschluss/Fehlerstromschutzeinrichtung @ 7\mod_1472029729200_370.docx @ 94314 @ @ 1
 Protect power supply with a ground fault circuit interrupter,
nominal residual current I
Pos: 106 /Technische Dokumentation/Betriebsanleitung/Installation/Elektrischer Anschluss/geeignete Leitungstypen @ 7\mod_1472030911381_370.docx @ 94368 @ @ 1
 Only use suitable pipe types according to regional
regulations.
Pos: 107 /Technische Dokumentation/Betriebsanleitung/Installation/Elektrischer Anschluss/Mindestquerschnitt @ 7\mod_1472031364414_370.docx @ 94386 @ @ 1
 Adjust minimum diameter of the electrical pipes to
accommodate the motor output and pipe length.
Pos: 108 /Technische Dokumentation/Betriebsanleitung/Installation/Elektrischer Anschluss/Leitung nicht knicken @ 8\mod_1472107268959_370.docx @ 94691 @ @ 1
 Do not bend or squash the pipes.
Pos: 109 /Technische Dokumentation/Betriebsanleitung/Installation/Elektrischer Anschluss/Not-Aus-Schalter nach DIN EN 809 @ 7\mod_1472038434346_370.docx @ 94404 @ @ 1
 If hazardous situations can occur, provide emergency off
switch according to DIN EN 809. The builder/operator must
make a decision according to this standard.
Pos: 110 /Technische Dokumentation/Betriebsanleitung/Installation/Elektrischer Anschluss/Bauseitiger Anschluss @ 8\mod_1472042559745_370.docx @ 94548 @ @ 1
 Connection by customer:
– Fuse protection 1-phase 230 V/3-phase 400 V safety fuse
16 A time delay or 16 A circuit breaker
– Short circuit breaking capacity I
Pos: 111 /Technische Dokumentation/Betriebsanleitung/Installation/Elektrischer Anschluss/Pumpen mit Kabel und Stecker @ 9\mod_1486654716486_370.docx @ 108391 @ @ 1
 Pumps with cables and plugs are wired ready for connection.
If the power cable is damaged, this must be replaced by the
manufacturer or the after-sales service in order to avoid any
danger.
Pos: 112 /Technische Dokumentation/Allgemeine Module/#### Seitenumbruch #### @ 0\mod_1426069111812_0.docx @ 891 @ @ 1
20 EN
≤ 30 mA.
FN
≤ 6 kA
CN
04|2017