LG LSXS22423 Manual De Usuario página 14

Ocultar thumbs Ver también para LSXS22423:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

3. DRILL THE HOLE FOR THE VALVE
Drill a 1/4" (6,35 mm) hole in
the water pipe using a sharp
bit. Remove any burrs
resulting from drilling the hole
in the pipe. Take care not to
allow water to drain into the
drill. Failure to drill a 1/4"
(6,35 mm) hole may result in reduced ice
production or smaller cubes.
NOTE: Licensed plumbers MUST use only cooper
tubing NDA tubing #49595 or 49499 or Cross
Link Polyethylene (PEX) tubing.
4. FASTEN THE SHUTOFF VALVE
Fasten the shutoff valve to the cold water pipe with
the pipe clamp.
Pipe Clamp
Saddle-Type
Shutoff Valve
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle
valves are illegal and use is not permitted in
Massachusetts. Consult with your licensed
plumber.
5. TIGHTEN THE PIPE CLAMP
Tighten the clamp screws until the sealing washer
begins to swell.
NOTE: Do not overtighten or you may crush the tubing.
Pipe Clamp
Clamp Screw
6. ROUTE THE TUBING
Route the tubing between the cold water line and the
refrigerator.
Route the tubing through a hole drilled in the wall or
floor (behind the refrigerator or adjacent base
cabinet) as close to the wall as possible.
NOTE: Be sure there is sufficient extra tubing [about 8
feet (2,4 m) coiled into 3 turns of about 10"
(25 cm) diameter] to allow the refrigerator to
move out from the wall after installation.
REFRIGERATOR INSTALLATION
7. CONNECT THE TUBING TO THE VALVE
NOTE: Commonwealth of Massachusetts Plumbing
8. FLUSH OUT THE TUBING
Vertical Cold
Water Pipe
9. CONNECT THE TUBING TO THE
REFRIGERATOR
NOTES:
• Before making the connection to the refrigerator, be
• If your refrigerator does not have a water filter, we
Washer
Inlet End
• Do not uses old hoses; only use new hoses provided by
1. Remove the plastic flexible cap from the refrigerator
2. Place the compression nut and ferrule (sleeve) onto
3. Insert the end of the tubing into the connection as
12
Place the compression nut and ferrule (sleeve) for
copper tubing onto the end of the tubing and
connect it to the shutoff valve. Make sure the tubing is
fully inserted into the valve. Tighten the compression
nut securely.
Saddle-Type
Shutoff Valve
Packing
Nut
Outlet
Valve
Codes 248CMR shall be adhered to. Saddle
valves are illegal and use is not permitted in
Massachusetts. Consult with your licensed
plumber.
Turn the main water supply on
and flush out the tubing until
the water is clear. Shut the water
off at the water valve after about
one quart (1 L) of water has been
flushed through the tubing.
sure the refrigerator power cord is not plugged into the
wall outlet.
recommend installing one. If your water supply has
sand or particles that could clog the screen of the
refrigerator's water valve, install the filter in the water
line near the refrigerator
the manufacturer.
connection.
the end of the tubing. (See figure 1)
far as possible. While holding the tubing, tighten the
fitting.(Part A)
CAUTION:
Check to make sure that leaks are not
occurring in the water line.
Compression
Nut
Ferrule(sleeve)

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Mfl62884312

Tabla de contenido