Peg-Perego Ypsi Instrucciones De Uso página 21

CLEANING THE CHASSIS: periodically clean all
plastic parts with a damp cloth. Do not use
solvent or similar cleaning products; keep all
metal parts dry to prevent rusting; keep moving
parts clean (adjustment mechanisms, locking
mechanisms, wheels, ...) and free of dust and
sand and, if necessary, lubricate with light
machine oil.
SEAT:
INSTRUCTIONS
1 OPENING: Before opening the Ypsi Seat, remove
(without using blades) any die-cut cardboard.
Open the seat from the ends, pulling until it
clicks.
2 ATTACHING THE SEAT ONTO THE CHASSIS: To
fasten the Ypsi Seat, position it on the chassis
(fig_a) and press down with both hands until it
clicks (fig_b).
Ensure the Ypsi Seat is properly attached.
3 The Ypsi Seat can be attached onto the chassis
in "world-facing" (fig_a) or "mum-facing"
position (fig_b).
4 Always engage the brake on the chassis before
fastening and unfastening the seat.
5 REMOVING THE YPSI SEAT FROM THE CHASSIS:
To unfasten the Ypsi Seat, press the levers near
the chassis attachments (fig_a) and lift the seat
at the same time (fig_b).
6 HOOD: to use the hood, stretch it until it clicks
(so it is completely open).
7 The hood comes with a mesh insert so that the
baby can be seen from any position. To use it,
open the zips (fig_a) and slide the hood's insert
backwards (fig_b). Alternatively, the hood can
be stretched further forwards (fig_c).
8 Sliding the hood's attachments on the uprights
(fig_a), you can vary its distance from the seat
(fig_b).
9 ADJUSTING THE LEG REST: To switch from
"sitting" to "lying" or vice versa, simply press
on the leg rest to obtain the configuration you
wish.
10 FRONT BAR: The front bar can be removed by
pushing the buttons on the sides (fig_a), or
it can be opened on one side pressing one
button only (fig_b).
11 BED POSITION: the seat can be adjusted in
three positions, from "sitting" to "lying", with an
intermediate position (fig_a). To switch from
one position to another, pull the lever shown in
the picture (fig_b).
12 5-POINT SAFETY HARNESS: to fasten, insert
the two buckles into the waist strap (with the
straps attached in the crotch strap) until you
hear a click (fig_a). To unfasten them, press
the button which is situated at the centre of
the seatbelt buckle and pull the waist strap
outwards (fig_b).
13 To tighten the waist strap, pull on both sides in
the direction of the arrow; to loosen it, do the
opposite.
14 The safety harness can be adjusted in 3
positions according to the child's height. You
must use the higher positions as the child
grows bigger.
15 Adjust the height, inserting the straps with
shoulder pads through the eyelet in the
backrest (fig_a) and pull them through the
desired eyelets (fig_b).
16 FOLDING THE YPSI SEAT ATTACHED ONTO THE
CHASSIS: the Ypsi Seat can be folded attached
on the cha ssis only in world-facing position
(fig_a).
To do this:
- the leg rest must be in "sitting" position,
- fold down the hood,
- pull the levers on the up-right (fig_b)
- fold Ypsi Seat onto itself (fig_c).
17 WARNING: If Ypsi Seat is in mum-facing
position, it must be unfastened before folding
(fig_a). It can take up less room when folded
(fig_b) and can be conveniently carried using
the supplied handle (fig_c).
18 OPENING THE CHASSIS WITH YPSI SEAT
ATTACHED:
Press the side attachment fastener downwards,
grip the upper ends of the handle bar and
rotate them towards you until the chassis
opens completely (fig_a). Ypsi chassis open
(fig_b). A "click" sound means it has opened
correctly and corresponds to the attachment
onto the base. Next, open the Ypsi Seat from
the ends, pulling it until it clicks (fig_c).
19 FOLDING THE CHASSIS WITH YPSI SEAT
ATTACHED: put the front wheels in locked
position (fig_a), lower the handle bar to the
lowest position (fig_b). Rotate the safety lever
to the left (fig_c) and, at the same time, pull the
frame's internal handle bar towards you (fig_d).
Lift the handle bar until the frame is completely
folded (fig_e).
WARNING: If the seat is mum-facing it cannot
be folded attached onto the chassis. It must be
unfastened.
20 To fold correctly, check the side fastener
is engaged (fig_a). If it has not engaged
automatically, compress the frame slightly. The
folded stroller is free-standing (fig_b).
21 TRANSPORT: the stroller can be conveniently
carried (with the front wheels in locked
position) using the central handle.
22 REMOVING THE SOFT COVER: to remove the
hood cover, unfasten the 2 buttons near the
pivots (fig_a), then press the buttons on the
two attachments and remove the hood (fig_b).
Lastly, extract the two rigid supports (fig_c).
23 To remove the soft cover from the seat, undo
the straps on the side of frame.
24 Open the zip that attaches the sack to the
horizontal bar (fig_a) and open the zip along
- 21 -