Precautions - Sony LMD-1041 Manual De Instrucciones

Tabla de contenido

Publicidad

Table of Contents

Precautions

Using the unit
• Use the unit under stable temperatures between 0 °C and
40 °C (32 °F and 104 °F).
• Prevent internal heat build-up by allowing adequate air
circulation. Do not place the unit on surfaces (rugs,
blankets, etc.) or near materials (curtains, draperies) that
may block the ventilation holes.
• Do not install the unit near heat sources such as radiators
or air ducts, nor in a place subject to direct sunlight,
excessive dust, mechanical vibration or shock.
• Do not place the unit near equipment which generates
magnetism, such as a converter or high voltage power
lines.
• Do not use the unit near equipment which generates a
strong electric field or radiation.
• Do not use the unit near an AM/FM tuner. The unit may
cause noise on the tuner.
• When you turn on the unit and display the video signal in
under-scan mode in low temperature, you may find jitter
or double-image. This is not a malfunction of the unit.
Wait for a few minutes until jitter or double-image
automatically disappears.
Notes on handling the LCD screen
• Do not leave the LCD screen facing the sun as it can
damage the LCD screen. Take care when you place the
unit by a window.
• Do not push or scratch the LCD screen. Do not put a
heavy object on the LCD screen. This may cause
malfunction and the display may not appear uniform.
• If the unit is used in a cold place, a residual image may
appear on the screen. This is not a malfunction of the unit.
When the unit becomes warm, the screen returns to
normal.
• If a still picture is displayed for a long time, a residual
image may appear. The residual image will disappear in a
while.
• Bright points of light (red, blue or green) may appear
constantly on the LCD screen. This is not a malfunction.
The LCD screen is made with high-precision technology
and has more than 99.9 % of effective picture elements.
However, 0.01 % of picture elements may not appear or
some picture elements may appear constantly.
• The screen and the cabinet become warm during
operation. This is not a malfunction.
Precautions .................................................................................................................. 3
Functions of Controls ................................................................................................. 4
Connections ................................................................................................................. 8
Installation ................................................................................................................... 9
Adjustments .............................................................................................................. 10
Using the unit in index mode ................................................................................. 11
Specifications ............................................................................................................. 12
Troubleshooting ........................................................................................................ 13
Replacement of the fluorescent tube
An exclusive fluorescent tube is installed as the lighting
apparatus of this unit. If the LCD screen becomes dark,
unstable or does not turn on, replace the fluorescent tube
with an new one. Consult your Sony dealer.
Power saving function
When there is no input signal, "NO. SYNC" appears on the
screen and the backlight turns off after about 5 seconds.
When a signal is input again, the backlight turns on
automatically.
If the fan motor stops suddenly
If the fan motor stops suddenly, the power of this unit is
turned off automatically to protect the fan motor.
If the fan motor stops suddenly, "WARNING" appears on
the LCD screen and the power is turned off after about 60
seconds. If this happens, disconnect the power cord and
consult your Sony dealer.
Maintenance
• Make sure to disconnect the power cord before cleaning
the unit.
• Avoid robbing the LCD screen as it can damage the LCD
screen. Use a dry and soft cloth to wipe the LCD screen.
• Clean the cabinet, panel and controls with a soft cloth
lightly moistened with a mild detergent solution. Do not
use any type of abrasive pad, scouring powder or solvent,
such as alcohol or benzine.
Notes on handling the remote
commander
• Handle the remote commander carefully. Do not drop or
step on the remote commander. Keep liquid away from
the remote commander.
• Do not place the remote commander under direct
sunlight, near heat sources or in a humid place.
J
EN
D
F
ES
I
3

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido