Peg-Perego book 51 S Instrucciones De Uso página 9

NOT MAKE ANY ALTERATIONS OR
MODIFICATIONS TO THE STROLLER
WITH PRODUCTS NOT SUPPLIED BY
THE MANUFACTURER AS THIS MAY
CAUSE INSTABILITY OR STRUCTURAL
DEMAGE NOT COVERED UNDER
WARRANTY.
NOTICE
THIS ARTICLE MEETS OR EXCEEDS
ALL REQUIREMENTS COVERED IN
ASTM F833 STANDARD AND LATEST
REVISIONS.
COMPONENTS OF THE ITEM
Check the contents of the packaging and if
you have any complaints please contact the
Assistance Service.
_ Book 51 S: basket; 2 rear wheels with brake
gear, rear wheel bar, 2 front wheels, solid
handle.
INSTRUCTIONS
1 OPENING: Before opening the frame, remove
(without using blades) any die-cut cardboard.
WARNING:
_ DO NOT PULL OR FORCE THE FASTENER
BEYOND ITS LIMIT.
_ DO NOT USE THE FASTENER AS A CARRY
HANDLE OR TO CARRY WEIGHTS.
DO NOT HANG BAGS OR OTHER ACCESSORIES
TO THIS FEATURE.
Press down the side fastener, hold the upper
section of the handle and rotate it towards you
until the frame is fully opened (fig_a). Open
frame (fig_b).
The frame is properly opened when the
attachment on the base clicks into place, as
shown. CAUTION: When placing the seat on the
frame, press the seat downwards to ensure it
engages securely onto the base.
2 FITTING THE WHEELS: Slot the uprights into
the rear wheel crosspiece (fig_a), ensuring
that it is facing the right way, then push the
rear wheels on and make sure that they click
into place (fig_b). To mount the front wheels, fit
them into the uprights until they lock into place
(fig_c).
3 ATTACHING THE MAIN HANDLE: if the handle
tube faces upwards, align it with the stroller
(Fig_a).
Fasten the handle to the frame as shown in
the figure (Fig_b).
To complete the operation, press the two
side buttons on the handle (Fig_c) to ensure
the handle pushes in all the way, until it clicks
into place (Fig_d).
4 FITTING THE BASKET: if lowered, lift the basket
tube to the horizontal position. Press the silver
buttons under the metal basket tube located at
the back of the stroller (fig_a) and remove the
metal tube (fig_b). Thread the tube through the
fabric loop on the back of the basket, making
sure that the two silver buttons are facing
downward (fig_c). Re-attach the tube to the
housings (fig_d).
5 Secure the two upper basket vinyl eyelets to the
two grey buttons on either side of the metal tube
housing. Please note that the eyelets open (fig_e).
Remove the cardboard from the lower rear bar.
IMPORTANT! Secure the two lower basket vinyl
eyelets to the two grey buttons on the top of the
lower rear bar. Please note that the eyelets open
(fig_f).
WARNING! If this operation is not performed
correctly, the basket will not properly hold the
weight.
Attach the basket tabs to the grey buttons on the
front of the frame (figure).
REFER TO OUR INSTALLATION INSTRUCTIONS
VIDEO AT:
WWW.PEGPEREGO.COM
6 FIXED OR SWIVEL FRONT WHEELS Book 51
S: to fix the front wheels, rotate the lever
counter clockwise to the locked padlock
(fig_a); to release the wheels, turn the lever
clockwise to the unlocked padlock (fig_b). On
difficult terrain, we recommend using fixed
wheels.
7 BRAKE: Press the lever down to apply the
brake on the chassis and lift it to release the
brake.
8 ADJUSTABLE HANDLEBAR: To adjust the
height of the handlebar, press both of the
side buttons at the same time (fig_a) and
swing it into the desired position (fig_b),
then release the buttons.
9 FOLDING UP: The chassis can be folded up
without the seat, with the seat facing the
person pushing (recline the backrest before
folding it) or with the seat facing forward.
To fold the stroller, it is best to set the front
wheels to their fixed position and close the
hood (if fitted). Place the handle as shown in
the figure (fig_a).
Pull the inside handle on the base (fig_b) and lift
it (fig_c); the handle will drop forward until the
frame is closed.
10 To ensure the frame is closed properly, check
that the side fastener is enabled (fig_a).
When closed, the frame remains in the
upright position (fig_b).
11 For greater compactness, it is possible to
remove the wheels.
To remove the rear wheels: pull outwards
on the lever located under the rear bar and
remove the wheels as shown in figure (fig_a).
To remove the front wheels: press the tab as
shown, and remove the wheel (fig_b).
- 9 -