REMS Krokodil 125 Instrucciones De Servicio página 13

Ocultar thumbs Ver también para Krokodil 125:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 27
eng
the clamping flange with the collar into the drive shaft and make sure that the 
lug of the drive shaft engages into the groove of the clamping flange. Press the 
drive shaft lock (18) and tighten the hexagon head bolt (10). Check the diamond 
cutting discs for secure fit. Swing the drive unit back in. Trial run the power tool 
with the newly fitted diamond cutting discs for at least one minute without load 
before starting work. The position of the diamond cutting discs can be marked
on the contact plate (9) for accurate positioning of the slits. 
CAUTION
Diamond cutting discs get very hot. Let them cool down before touching or
removing.
2.4. Setting the switch handle and holding handle
REMS Krokodil 125 (Fig. 1 and 2)
Pull out the mains plug. The switch handle (1) can be mounted parallel to the 
machine axle and swivelled 90°. To do this, loosen the clamping screw of the
switch handle (2) and set the switch handle to the desired position, tighten the 
switch handle clamping screw. The holding handle (3) can be mounted swivelled 
in several detent positions. To do this, open the clamping screw of the holding
handle (4) until the teeth no longer engage. Move the holding handle into the 
desired position (pay attention to positive lock of the teeth) and tighten with the 
holding handle's clamping screw.
REMS Krokodil 180 (Fig. 3 and 4)
Pull out the mains plug. The holding handle (3) can be mounted swivelled in 
several detent positions. To do this, open the clamping screw of the holding
handle (4) until the teeth no longer engage. Move the holding handle into the 
desired position (pay attention to positive lock of the teeth) and tighten with the 
holding handle's clamping screw (4). By removing the holding handle's clamping 
screw (4) the holding handle (3) can be mounted turned 180°. Move the holding 
handle into the desired position (pay attention to positive lock of the teeth) and 
tighten with the holding handle's clamping screw (4).
2.5. Setting the depth stop
REMS Krokodil 125 (Fig. 1 and 2)
Pull out the mains plug. Undo the holding handle's clamping screw (4) about 
1 turn. To set the slitting depth, move the depth stop (5) to the desired position
and tighten with the holding handle's clamping screw (4).
REMS Krokodil 180 (Fig. 3 and 4)
Pull out the mains plug. Undo the depth stop clamping screw (20) about ½ a 
turn. To set the slitting depth, move the depth stop (5) to the desired position 
and tighten with the depth stop clamping screw (20).
2.6. Dust extraction
WARNING
Inhalation of the dusts produced when slitting and cutting is harmful to the
health. Observe the national regulations. It is recommended to use a safety
vacuum cleaner/dust extractor of dust class M. Observe the operating instruc-
tions of the safety vacuum cleaner/dust extractor.
Push the suction nozzle adapter (16) onto the suction nozzle (15) on the REMS 
Krokodil 125 so that the greatest possible distance of the pushed on suction
hose from the contact plate is achieved (Fig. 1).
No adapter is required for the suction nozzle on the REMS Krokodil 180.
2.7. Fixing the workpiece
Workpieces which are slit or cut loosely must be rigidly fixed and secured 
against being flung away.
2.8. Note on static
Before beginning work, make sure that the building static is not negatively
affected by the slitting or cutting work; consult the building management or a
static engineer if necessary. Slitting work in supporting walls may be subject
to national regulations. These regulations must be observed.
3. Operation
Use eye protection
Use ear protection
Suitable safety vacuum cleaners/dust extractors, a respirator and disposable
overalls must be used for work which could produce health hazardous dusts.
Observe the national regulations.
REMS Krokodil 125 and REMS Krokodil 180 are fitted with a safety switch with 
lock (8). This enables the drive unit to be shut down at any time and prevents 
unintentional staring of the drive unit. The safety switch with lock must first be 
pushed in the direction of the mains lead and then pressed on the REMS
Krokodil 125. On the REMS Krokodil 180 first the locking button on the side of 
the switch handle (1) and then the safety switch must be pressed.
In order to simplify handling and to avoid damage, REMS Krokodil 125 and
REMS Krokodil 180 must be equipped with multi-function electronics with
electronic speed control or speed regulator. The multi-function electronics
perform the following functions:
3.1. Slitting
Use a respirator
Use hand protection
3.2. Cutting
● Electronic start-up current limiting reduces the inrush current and therefore
allows operation on a 16 A fuse.
● Soft start for protecting the drive unit and jolt-free starting after switching on.
● Limiting of the idle speed to reduce noise and preserve the motor and gear.
● Overload protection of the motor depending on the thrust pressure. The
motor current and thus the speed of the drive machine is reduced to a
minimum before overloading of the drive unit due to too high a thrust pres-
sure on the diamond cutting discs or blocking. However, the drive unit does
not switch off. If the thrust pressure is reduced, the speed of the drive unit
increases again. This process does not damage the drive unit even if it is
repeated several times. If the motor remains at standstill despite reducing
the thrust pressure, however, the drive unit must be switched off and the
diamond cutting discs may have to be re-engaged.
REMS Krokodil 125
Use a suitable safety vacuum cleaner/dust extractor. Hold the REMS Krokodil
125 by the switch handle (1) and holding handle (3) and set the contact plate
(9) against the surface to be machined. Make sure you have a safe footing and
enough room for the drive unit, safety vacuum cleaner/dust extractor, suction
hose and user. Safety vacuum cleaner/dust extractor. Switch on the REMS
Krokodil 125 at the switch handle. To do this, first push the safety switch with 
lock in the direction of the mains lead and then press it. When the power tool
has reached full speed, press the REMS Krokodil 125 onto the surface with
even thrust pressure. The diamond cutting discs penetrate the surface. On
reaching the slitting depth, push the REMS Krokodil 125 forward against the
direction of the arrow (14) because otherwise the cutting disc could lift uncon-
trolled out of the slit. Make sure that the diamond cutting discs do not twist/jam.
After finishing the slit, switch off the REMS Krokodil 125 and wait until the 
diamond cutting discs have come to a complete standstill. Do not lift off the
surface until the drive unit is at a standstill. Switch off the safety vacuum cleaner/
dust extractor.
CAUTION
Diamond cutting discs get very hot. Let them cool down before touching or
removing.
Make sure that the suction hose of the industrial vacuum cleaner does not kink
and impair the dust extraction. Also make sure that no fragments of stone or
other objects jam in the suction nozzle (15) and/or suction hose. Empty the 
dust bag of the safety vacuum cleaner/dust extractor early and clean/renew
the filter regularly. Observe the operating instructions of the safety vacuum 
cleaner/dust extractor.
After slitting, a ridge remains between the slits. This can be broken out with a
slitting chisel (part no. 185024).
REMS Krokodil 180
Use a suitable safety vacuum cleaner/dust extractor. Hold the REMS Krokodil
180 by the switch handle (1) and holding handle (3) and set the contact plate 
(9) against the surface to be machined. Make sure you have a safe footing and 
enough room for the drive unit, safety vacuum cleaner/dust extractor, suction
hose and user. Safety vacuum cleaner/dust extractor. Switch on the REMS
Krokodil 180 at the switch handle. To do this, first press the lock button on the 
side of the switch handle (1) and then press the safety switch (8). When the 
power tool has reached full speed, press the REMS Krokodil 180 onto the
surface with even thrust pressure. The diamond cutting discs penetrate the
surface. On reaching the slitting depth, push the REMS Krokodil 180 forward
in the direction of the arrow (14) because otherwise the cutting disc could lift 
uncontrolled out of the slit. Make sure that the diamond cutting discs do not
twist/jam. After finishing the slit, switch off the REMS Krokodil 180 and wait 
until the diamond cutting discs have come to a complete standstill. Do not lift
off the surface until the drive unit is at a standstill. Switch off the safety vacuum
cleaner/dust extractor.
CAUTION
Diamond cutting discs get very hot. Let them cool down before touching or
removing.
Make sure that the suction hose of the industrial vacuum cleaner does not kink
and impair the dust extraction. Also make sure that no fragments of stone or
other objects jam in the suction nozzle (15) and/or suction hose. Empty the 
dust bag of the safety vacuum cleaner/dust extractor early and clean/renew
the filter regularly. Observe the operating instructions of the safety vacuum 
cleaner/dust extractor.
After slitting, a ridge remains between the slits. This can be broken out with a
slitting chisel (part no. 185024).
REMS Krokodil 125
Use a suitable safety vacuum cleaner/dust extractor. Only insert one diamond
cutting disc in the machine. Secure/clamp the workpiece to be cut. Hold the
REMS Krokodil 125 by the switch handle (1) and holding handle (3) and setthe
contact plate (9) against the workpiece to be cut. Make sure you have a safe
footing and enough room for the drive unit, safety vacuum cleaner/dust extractor,
suction hose and user.. Safety vacuum cleaner/dust extractor. Switch on the
REMS Krokodil 125 at the switch handle. To do this, first push the safety switch 
in the direction of the mains lead and then press it. On reaching full speed,
press the REMS Krokodil 125 against the workpiece with even thrust pressure
eng

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Krokodil 180 sr

Tabla de contenido