Specific Safety Rules And Symbols - Metabo HPT DS 12DVF3 Manual De Instrucciones

Taladro atornillador a bateria
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

English
WARNING:
Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities
contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
● Lead from lead-based paints,
● Crystalline silica from bricks and cement and other
masonry products, and
● Arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic particles.

SPECIFIC SAFETY RULES AND SYMBOLS

1.
Wear ear protectors when impact drilling.
Exposure to noise can cause hearing
loss.
2.
Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
3.
Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring.
Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
4.
Hold power tool by insulated gripping surfaces,
when performing an operation where the fastener
may contact hidden wiring.
Fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
5.
NEVER place hands or other body parts near the
drill bit or chuck during operation. Hold the drill
by its handle only.
6.
Because the cordless driver drill operates by
battery power, be aware of the fact that it can begin
to operate at any time.
7.
When working at elevated locations, clear the area
of all other people and be aware of conditions
below you.
8.
NEVER touch moving parts.
NEVER place your hands, fingers or other body
parts near the tool's moving parts.
9.
NEVER operate without all guards in place.
NEVER operate this tool without all guards or
safety features in place and in proper working
6
order. If maintenance or servicing requires the
removal of a guard or safety feature, be sure to
replace the guard or safety feature before resuming
operation of the tool.
10. Use right tool.
Don't force small tool or attachment to do the job
of a heavy-duty tool.
Don't use tool for purpose not intended —for
example— don't use circular saw for cutting tree
limbs or logs.
11. NEVER use a power tool for applications other
than those specified.
NEVER use a power tool for applications other than
those specified in the Instruction Manual.
12. Handle tool correctly.
Operate the tool according to the instructions
provided herein. Do not drop or throw the tool.
NEVER allow the tool to be operated by children,
individuals unfamiliar with its operation or
unauthorized personnel.
13. Keep all screws, bolts and covers tightly in place.
Keep all screws, bolts, and plates tightly mounted.
Check their condition periodically.
14. Do not use power tools if the plastic housing or
handle is cracked.
Cracks in the tool's housing or handle can lead to
electric shock. Such tools should not be used until
repaired.
15. Blades and accessories must be securely mounted
to the tool.
Prevent potential injuries to yourself or others.
Blades, cutting implements and accessories which
have been mounted to the tool should be secure
and tight.
16. NEVER use a tool which is defective or operating
abnormally.
If the tool appears to be operating unusually,
making strange noises, or otherwise appears
defective, stop using it immediately and arrange
for repairs by a metabo HPT authorized service center.
17. Carefully handle power tools.
Should a power tool be dropped or struck against
hard materials inadvertently, it may be deformed,
cracked, or damaged.
18. Do not wipe plastic parts with solvent. Solvents
such as gasoline, thinner benzine, carbon
tetrachloride, and alcohol may damage and crack
plastic parts. Do not wipe them with such solvents.
Wipe plastic parts with a soft cloth lightly
dampened with soapy water and dry thoroughly.
19. ALWAYS wear eye protection that meets the
requirement of the latest revision of
ANSI Standard Z87.1.

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Ds 14dvf3Ds 18dvf3

Tabla de contenido