STAMOS S-WIGMA 200 PRO Manual De Instrucciones página 7

5.1. PREPARING THE DEVICE FOR USE / DEVICE USE
Each unit is equipped with a main power cable, which
is responsible for providing current and voltage to the
device. If the device is connected to power which exceeds
the required voltage, or if the wrong phase is set, it may
lead to severe damage to the unit. This is not covered
by the warranty for the equipment and the user will be
responsible for such situations.
5.2. DEVICE USE
METHOD TIG
• Turn the main switch on the front panel to „On", the
fan will start rotating.
• Open the argon cylinder valve, adjust the gas flow
volume making sure it is appropriately set for welding.
• Press the torch button, which will activate the solenoid
valve. You will hear the sound of the HF arc and at the
same time, argon will flow from the nozzle.
PLEASE NOTE: During the first welding the user must
keep pressing the torch switch for a few seconds
until all air escapes.
• Set the welding current and make sure it is
appropriate for the selected type of welding.
• Bring the tungsten electrode 2 to 4 mm from the
workpiece. Press the torch button, you will hear the
arc ignite. The machine is ready for use.
• PLEASE NOTE: After welding is finished, argon will
still flow for a few seconds in order to protect the
weld area from cooling. The torch must be kept
close to the welding spot for some time after the arc
extinguishes.
1. Set the switch (10) to TIG welding mode.
2. Connect the return lead to the correct socket, marked
with the number 5 on the diagram and tighten the
locking nut.
3. Then remove the cap and connect the welding lead to
the socket, marked with the number 6 on the diagram
and tighten the locking nut. Connect the remaining
leads to the socket marked with the number 7 on the
diagram – control socket and to the socket market
with the number 8 on the diagram – gas connection
socket.
EN
4. Then connect the gas source to the connector on the
back of the machine.
5. Once the machine is correctly assembled, connect the
power lead and switch
TIG Torch
1
2
3
4
5
6
1. Cap, long
2. Cap, short
3. Collet
4. Torch handle
5. Collet inside housing
6. Ceramic nozzle
MMA METHOD
• Turn the main switch on the front panel to „On", the
fan will start rotating.
• Make sure the TIG/ MMA switch is switched "down"
to MMA. Pulse change switch and gas flow knob will
not work.
• Set the welding current and make sure it is
appropriate for the selected type of welding.
1. Set the switch (10) to MMA welding mode.
2. Connect the return lead to the correct socket, marked
with the number 5 on the diagram and tighten the
locking nut.
3. Then connect the welding lead to the correct socket,
marked with the number 6 on the diagram and
tighten the locking nut.
ATTENTION! Polarization of the leads has to be
different! All polarisation information should be
shown on the packaging supplied by the electrode
manufacturer.
4. Once the machine is correctly assembled, connect the
power lead and switch it on.
12
WARNING: during welding, it is forbidden to pull the plug
or the cable that is being used. It may result in damage to
the unit and/or risk of death.
Advice for use:
• The temperature of environment must not be higher
than 40°C and the relative humidity should be less
than 90%.
• Avoid welding in direct sunlight and/or rain.
• Do not use the machine in environments containing
dust or corrosive gas.
• Avoid TIG welding in a strong wind.
• When the voltage, output current and machine
temperature exceed the nominal values, the unit will
automatically switch off. Current overload can cause
damage and destroy the machine.
• After exceeding the operating cycle, the unit will
stop working. When the main switch is in the "ON"
position and the machine overloads, the overload
indicator lights up (red LED). Do not pull the plug
from the power supply so that the fan can cool the
machine down. When the temperature drops, the
overload indicator turns off and you can continue
welding.
6. DISPOSING OF PACKAGING
The various items used for packaging (cardboard, plastic
straps, polyurethane foam) should be kept, so that the
device can be sent back to the service centre in the best
possible condition in case of any problems!
7. TRANSPORTATION AND STORAGE
Shaking, crashing and turning upside down of the device
should be prevented while it is transported. Store it in
a properly ventilated surrounding with dry air and without
any corrosive gas.
8. CLEANING AND MAINTENANCE
• Disconnect from electricity when cleaning
equipment.
• Use cleaner without corrosive substances to clean
surface.
• Dry all parts well after cleaning before the device is
used again.
• Store the unit in a dry, cool location, free from
moisture and direct exposure to sunlight.
• Regularly remove dust with dry and clean
compressed air.
9. REGULAR CONTROL OF THE DEVICE
Check regularly that the device doesn´t present any
damage. If there is any damage, please stop using the
device. Please contact your customer service to solve the
problem.
What to do in case of a problem?
Please contact your customer service and prepare following
information:
• Invoice number and serial number (the latter is to be
found on the technical plate on the device).
• If relevant, a picture of the damaged, broken or
defective part.
• It will be easier for your customer service clerk
to determine the source of the problem if you
give a detailed and precise description of the
matter. The more detailed your information, the
better the customer service will be able to help
you with your problem rapidly and efficiently!
CAUTION: Never open the device without the authorization
of your customer service. This can lead to a loss of warranty!
EN
13