Using.the.intercom; Introduction; Intercom.compatibility; Before.starting.the.intercom - SCHUBERTH SRC‑SYSTEM S2 Manual De Instrucciones

9. USING THE INTERCOM

9.1 INTRODUCTION

Your.SRC-System™.allows.you.to.connect.to.other.bikers.using.SRC.headsets.
within.a.range.of.up.to.700.meters./.2,300.ft..(subject.to.terrain)..To.set.up.one.
or.two.Intercom.Bluetooth®.connections,.you.must.first.pair.your.SRC-System™.
headset.with.the.other.headsets..
Pairing.is.a.one.time.process..Once.completed,.the.headsets.will.remain.paired.
and.automatically.recognize.each.other.whenever.they.are.within.range.
Your.headset.has.two.Intercom.channels.available.for.headset-to-headset.
connections..Therefore,.your.SRC-System™.can.communicate.simultaneously.in.
conference.mode.with.up.to.two.other.SRC.headsets..
9.2 INTERCOM COMPATIBILITY
You.can.use.your.SRC-System™.headset.for.Intercom.communication.with.any.
other.SRC-System™.headset.and.with.cardo.scala.rider.headsets..For.further.
details.visit.www.cardosystems.com/SRC.
9.3 BEFORE STARTING THE INTERCOM
Your.SRC-System™.headset.has.two.buttons.designated.for.quick.connection.to.
two.other.headsets..These.other.headsets.are.referred.to.as.CHANNEL "A".and.
CHANNEL "B".
Channel "A"
Button
Before.you.can.begin.using.the.intercom.for.Bike-to-Bike.communication.with.
one.or.two.other.headsets,.all.units.must.first.be.paired..
MAN00097 QG SRC-S2_C3 J 009.indd 41
Channel "B"
Button
9.4 USING THE SRC‑SYSTEM™ FOR INTERCOM WITH OTHER SRC‑SYSTEM™
HEADSETS
INTERCOM CHANNEL PAIRING / CONNECTION
BUTTON
CHANNEL."A" CHANNEL."A".BUTTON
CHANNEL."B" CHANNEL."B".BUTTON
9.4a. TWO‑WAY INTERCOM
Using.two.SRC-System™.headsets.
1.. While.both.headsets.are.turned.OFF,.turn.them.ON.by.pressing.and.holding.
the.Mobile.Buttons.until.the.Blue.Lights.flash.three.times.
2.. Make.sure.that.both.headsets.are.now.flashing.slowly.in.Blue..
3.. Choose.an.available.CHANNEL.you.wish.to.use.to.pair.the.headset.(CHANNEL.
"A".or.CHANNEL."B").
NOTE: Selecting a CHANNEL that is already in use will override the paired headset on
that CHANNEL with the newly paired headset.
4.. . O n.the SRC-System™.headset,.press.and.hold.the.assigned.CHANNEL.BUTTON.
("A".or."B").for.at.least.six.seconds.until.the.headset's.BLUE.or.RED.Light.be-
gins.flashing.rapidly,.indicating.it.is.in.Intercom.Pairing.mode..(See.Intercom.
Channel.Table.for.Pairing.LED.indication.for.each.CHANNEL).
5.. Repeat.Step.3-4.for.the.second.SRC-System™.
6.. Within.a.few.seconds,.both.headsets.will.show.a.solid.light.for.two.seconds,.
indicating.that.the.two.headsets.are.now.paired,.connected.and.ready.for.use.
NOTE: If the Pairing process is not completed within two minutes the headset will
return to Standby mode.
PAIRING MODE LED
INDICATORS
Rapid.RED.flashing
Rapid.BLUE.flashing
41
7/18/12 5:38 PM