Preparing Hot Water; Changing And Saving The Cup Measure - Fagor CAT 40 NG Instrucciones De Uso

Máquina automática para café expresso
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Attention! Impurities from dried milk
residues in the steam nozzle. Take care
not to immerse the steam nozzle in the
milk far enough to cover the air intake
opening at the top of the steam nozzle.
Otherwise milk can be sucked into the
nozzle and cause impurities in the
steam nozzle.
Turn the Selection dial for steam and
hot water (Fig. 1, D) to the
tion (Fig. 17). The milk is now frothed
up.
Hold the mug steady during the froth-
ing. The nozzle should not be allowed
to touch the bottom of the mug and
cut off the steam supply. Froth the milk
to at least twice its volume.
To stop frothing, turn the Selection dial
for steam and hot water (Fig. 1, D) to
the
position and remove the jug
(Fig. 17).
Caution! Danger of scalding from hot
milk spray! Switch the steam off,
before removing the jug with the
frothed milk.
To finish steam mode, press the "Steam
Pre-selector" key (Fig. 3, e)
ca. 60 sec., for the machine to auto-
matically return to the coffee mode.
The indication is extinguished.
The coffee machine is now ready for
making coffee again.
Each time you have frothed milk, let
off some hot water through the nozzle
for a short time by setting the Selec-
tion dial for steam and hot water (Fig.
1, D) to the
position. This is nec-
essary to prevent milk residues drying
inside the nozzle, and thereby blocking
it. Use a suitable container to catch the
water.
Remove the frothing aid after each use
(Fig. 18). For this, take hold of the
frothing aid by the black seal and dis-
engage the bayonet connector by
turning it slightly anticlockwise. R inse
off the milk residues under running
water. Wipe the steam nozzle off with
a damp cloth.
Caution! Danger of burns from the
frothing aid! Hold the frothing aid only
by the black seal.
8

Preparing Hot Water

The hot water can be used to pre-heat
u c
s p
n a
or instant soups.
posi-
Caution! Danger of scalding when the
hot water nozzle is activated! Hot
water or steam output can cause
scalding. Activate the hot water nozzle
only when a container is under the hot
water nozzle.
Place a container under the hot water
nozzle. Set the Selection dial for steam
and hot water (Fig. 1, D) to the
position (Fig. 19). Hot water is now
prepared.
After you have dispensed the hot water
turn the Selection dial for steam and
hot water (Fig. 1, D) back to the
position (Fig. 19) and remove the con-
tainer.
9
Changing and Saving the
, or wait
Cup Measure
The coffee machine is factory-set to
standard measures. These measures can
be individually changed to your own
taste and saved for each cup size. The
adjustment can take place in both
bean and powder mode. The setting of
"Cup Measure" is only possible for
1 cup. When dispensing 2 cups the
"Cup Measure" is doubled.
Repeatedly press the "Cup Size" key
(Fig. 3, d)
which you wish to change the measure,
is illuminated.
Place the appropriate cup under the
coffee dispenser (e.g. coffee mug).
Press and hold the Key for 1 cup of
coffee (Fig. 3, b)
is filled to the desired measure. Release
the key. Your new cup measure is now
saved.
f d
r o
m
k a
n i
h g
t o
r d
n i
s k
e ,
until the cup symbol, for
until the cup/mug
GB
g .
t .
a e
39

Publicidad

Tabla de contenido
loading

Tabla de contenido