Electrical Safety - Stanley STGB3715 Manual De Instrucciones

or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.

6. Electrical safety

Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
STANLEY Service Center or an equally qualified
person in order to avoid damage or injury. If the
power cord is replaced by an equally qualified
person, but not authorized by STANLEY, the
warranty will not be valid.
7. Labels on tool
The label on your tool may include the following symbols:
Hz .......
Read
Instructions
W ........
Manual
min .....
Use Eye
Protection
Use Ear
Protection
V ........ Volts
n .......
0
A ........ Amperes
ADDITIONAL SAFETY RULES
FOR BENCH GRINDERS
f Always use proper guard with grinding wheel. A guard
protects operator from broken wheel fragments.
f Accessories must be rated for at least the speed
recommended on the tool warning label.Wheels and
other accessories running over the rated speed can fly
apart and cause injury.
f Before using, inspect recommended accessory for
cracks or flaws. If such a crack or flaw is evident,
Hertz
...... Class II
Watts
....
minutes
..... Alternating
....
Current
..... Direct
.../min..
Current
No-Load
Speed
discard the accessory. DO NOT USE A GRINDING
WHEEL THAT IS CRACKED OR FLAWED IN ANY WAY.
f When starting the tool, let it run for one minute. Never
start the tool with a person in line with the wheel. This
includes the operator.
f Do not grind on the sides of grinding wheels unless
they are specifically designed for that purpose.
f Do not overtighten wheel clamp nut. This may crack
the grinding wheel.
f Clean the cavity around the grinding wheel periodically.
Warning! Some dust created by power sanding,
sawing, grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth defects
or other reproductive harm. Some examples of these
chemicals are:
f lead from lead-based paints,
f crystalline silica from bricks and cement and other
masonry products, and arsenic and chromium from
chemically-treated lumber. (CCA)
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: Work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that
are specially designed to filter out microscopic particles.
f Wear protective glasses;
f Do not use damaged or unshaped wheels;
f The adjustment of the spark arrestor shall be made
frequently, so as to compensate the wear of the wheel,
keeping the distance between the guard and the
wheel as small as possible, but in any case not greater
than 2mm;
f The adjustment of the work rest shall be done
gradually so as to compensate the wear of the wheel,
Construction
keeping the distance between the work rest and the
Earthing
wheel as small as possible, but in any case not greater
Terminal
than 2mm;
Safety Alert
Symbol
BENCH MOUNTING
Revolutions
or Recipro-
1. The grinder should be unplugged.
cation per
2. Position grinder on workbench. Check for the
minute
availability of power for the grinder. Mark location
of holes for drilling.
3. Drill appropriate sized holes.
4. Insert 1/4" (6mm) Hex head bolts through washers
and the holes. You may want to use washers on
the underside of the bench as well.
5. Tighten the nuts. Do not overtighten. Allow the rubber
feet to absorb the vibration when the grinder is running.
ENGLISH • 13