Grass Cutting; Controls Description - Stiga T 484 Series Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 38
NOTE – The number which precedes each paragraph
links the references in the text to the respective illus-
trations (listed on page iii and following pages).
1. COMPLETE ASSEMBLY
NOTE The machine can be supplied with some parts al-
ready assembled.
WARNING!
Unpacking and completing the assem-
bly should be done on a flat and stable surface, with
enough space for moving the machine and its packag-
ing, always making use of suitable equipment.
Disposal of the packaging should be done in accord-
ance with the local regulations in force.
1.1 Assembling the rear discharge guard
Push the pin (1) to the right as shown.
Fit this tip in the right seat (2) of the chassis, fasten the eye-
let terminal (3) of the spring with a screwdriver then insert
it into the slit; then fit the left tip of the pin into its respec-
tive seat (4).
1.2 Assembling the handle
Insert the lower right part (1) of the handle into the respec-
tive chassis housing; hold the plate (2) in position inside the
chassis, then fit the right cover (3) and fasten all of it with
the supplied screws (4).
Assemble the left bottom part (5) of the handle and the left
cover (6) with the screws (7) and then the top part of the
handle (8) with the nuts and bolts (9).
Assemble the starter cable's guide spring (10) and fasten
the control cables with the binders (11).
1.3 Assembling the dashboard
Assemble the dashboard (1) following the indicated steps.
1.4a Assembling the grass catcher (Type"I")
Assemble the two parts (1) and (2), making sure you have
securely inserted the fittings in their seats until they snap
into place.
1.4b Assembling the grass catcher (Type"lI")
Insert the frame (11) in the grass catcher (12) and snap
on all the plastic sections (13), using a screwdriver as il-
lustrated.
1.4c Assembling the grass catcher (Type"lIl")
Turn the plastic part (22) over, then insert all the slots on the
outer edge (23) of the fabric part (21) onto the hooks on the
plastic part, starting at the end.
Fit the two side elements of the frame (25) into the loops
in the fabric. Insert the two ends of the frame (25) into their
slots and snap the plastic section (26) onto the frame's
middle part.
Use the screws (27) to fasten the frame to the plastic part.
1.5 Battery connection
In electric ignition system models, connect the battery ca-
ble to the general wiring connector on the lawnmower.

2. CONTROLS DESCRIPTION

NOTE The meanings of the symbols on controls are ex-
plained in the previous pages.
2.1 Throttle lever
The throttle is controlled by the lever (1).
Lever positions are indicated on the relevant plate.
Some models have a fixed speed engine with no need for
a throttle.
2.2 Engine brake lever / cutting means
The cutting means brake is controlled by the lever (1) which
must be held against the handle during ignition and during
lawnmower operations.
The engine stops when the lever is released.
2.3 Drive lever (where applicable)
On power-driven models, push the lever (1) toward the han-
dle for forward movement.
The lawnmower stops moving forward when the lever is
released.
The engine must always be ignited with the drive disen-
gaged.
WARNING!
sion, do not pull the machine backwards with the
transmission engaged.
2.4 Cutting height adjustment
The cutting height is adjusted by the levers (1-2).
The four wheels must be adjusted to the same height.
DO THIS WHEN THE CUTTING MEANS IS STATIONARY.

3. GRASS CUTTING

NOTE
This machine can be used to mow lawns in a
number of different ways; before starting work, prepare the
machine based on how the lawn is to be mowed.
DO THIS WHEN THE ENGINE IS OFF.
3.1 Preparation for mowing and grass collection by
the grass catcher
Raise the rear discharge guard and fasten the grass catch-
er (1 or 2) correctly in place, according to the different pro-
cedures foreseen for each type used.
3.2 Engine ignition
During ignition, follow the instructions in the engine man-
ual, then pull the cutting means brake lever (1) against the
handle and firmly tug the knob on the ignition cable (2).
If the model has an electric ignition system, pull the cut-
ting means brake lever (1) against the handle and turn the
ignition key (3).
3.3 Mowing the lawn
The appearance of the lawn will improve if you alternate
cutting in both directions at the same height.
When the grass catcher is too full, grass collection is no
longer efficient and the sound of the lawnmower changes.
To remove and empty the grass catcher,
– stop the engine and wait for the cutting means to stop;
– lift the rear discharge guard, grasp the handle and re-
move the grass catcher keeping it in an erect position.
Lawn care recommendations
Each type of grass has different characteristics and may
thus require different ways of caring for the lawn; always
read the instructions on seed boxes for mowing height for
EN - 4
To prevent damage to the transmis-

Publicidad

Tabla de contenido
loading

Tabla de contenido