Ravelli HRB 150 Manual De Uso Y Mantenimiento página 54

pressing in continue the button P2 and P5 the Set of the temperature environment can be planned by a value min
of 7 °C to a maximum value of 40 °C.
- Make sure to check the pellet level in the hopper so that the flame does not go out due to lack of fuel.
- Make sure the unit is off when loading pellets.
Rev.1 14/02/18
- The pellet hopper cover must always remain closed, to be opened only during fuel loading.
Pag.54
- The bags of pellets must be kept at least 1.5 m from the insert.
EN
If the STANDBY mode is not activated and the set temperature is reached, or if the fume temperature has reached
the set maximum value, the LCD display shows the message MODULATE or MODULATE F and the stove activates
The bags of pellets must be kept at least 1.5 m from the insert. In case of persistent failed lighting, contact the
the flame modulation procedure without any intervention by the user.
Service Center.
If, on the other hand, STANDBY mode is activated, the stove activates the modulation mode for a few minutes
when the SET temperature is reached. If the temperature remains above the set value, the stove shuts down.
If the STANDBY mode is not activated and the set temperature is reached, or if the fume temperature has reached the set maximum
Restart occurs after the room temperature falls below the set value by a few degrees (default 2°C).
value, the LCD display shows the message MODULATE or MODULATE F and the stove activates the flame modulation procedure
If the temperature increases again, above a set limit, the HOT FUMES alarm appears and the insert activates the
without any intervention by the user. If, on the other hand, STANDBY mode is activated, the stove activates the modulation mode for
shutdown procedure.
a few minutes when the SET temperature is reached. If the temperature remains above the set value, the stove shuts down.
During normal operation, the BRAZIER CLEANING mode is activated for several seconds at fixed intervals.
Restart occurs after the room temperature falls below the set value by a few degrees (default 2°C). If the temperature increases
again, above a set limit, the HOT FUMES alarm appears and the insert activates the shutdown procedure. During normal operation,
the BRAZIER CLEANING mode is activated for several seconds at fixed intervals. 4.2.3 Shutdown
To shut down the stove , just press button P3 for about 3 seconds. The auger is immediately stopped and the fume
Shutdown
exhaust fan goes to high speed, with the message FINAL CLEANING appearing on the display. The fume exhaust
To shut down the stove , just press button P3 for about 3 seconds. The auger is immediately stopped and the fume exhaust fan
will remain on until the insert temperature has fallen sufficiently.
goes to high speed, with the message FINAL CLEANING appearing on the display. The fume exhaust will remain on until the insert
At the end of the operation the message OFF will appear on the display.
temperature has fallen sufficiently. At the end of the operation the message OFF will appear on the display. During the shutdown
During the shutdown phase the stove cannot be restarted until the fume temperature has dropped below a fixed
phase the stove cannot be restarted until the fume temperature has dropped below a fixed value for a given time. If the on button is
value for a given time. If the on button is pressed the message AWAITING COOL will be displayed.
pressed the message AWAITING COOL will be displayed.
4.2.4 Additional remote control functions
Additional remote control functions
The display on the remote control shows all the information on stove operation. The basic functions are:
The display on the remote control shows all the information on stove operation. The basic functions are:
STATUS
OFF
START
PELLET LOADING
AWAITING FLAME
FLAME PRESENT
WORK
MODULATE– MODULATE F
BRAZIER CLEANING
FINAL CLEANING
STANDBY
AWAITING COOL-
The remote control has a keylock function. This is available only if enabled by the specialized technician during the first installation.
The remote control has a keylock function. This is available only if enabled by the specialized technician during the
From the main menu, press buttons P5 and P3 in rapid succession, to activate or deactivate the keylock function. The two messages
first installation. From the main menu, press buttons P5 and P3 in rapid succession, to activate or deactivate the
shown opposite appear on the display. Press button P5 to access the list of submenus. They allow the electronic controller settings
keylock function. The two messages shown opposite appear on the display.
to be changed. The various submenus can be scrolled by pressing buttons P1 and P2, and can be accessed by pressing button P5
Press button P5 to access the list of submenus. They allow the electronic controller settings to be changed. The
and exited by pressing P3.
various submenus can be scrolled by pressing buttons P1 and P2, and can be accessed by pressing button P5 and
exited by pressing P3.
MENU 01 – Adjust fans
Non available function.
MENU 01 – Adjust fans
Non available function.
MENU 02 – Set clock
Before operating the stove , the current time and date must be set in order to have a reference for possible chrono programming.The
MENU 02 – Set clock
electronic control has a 3-volt lithium battery model CR2032 that gives the internal clock an operation autonomy; battery replacement
Before operating the stove , the current time and date must be set in order to have a reference for possible chrono
is necessary if the clock does not keep the time with the stove not powered, or a series of zeros appears at restart: call an authorized
programming.The electronic control has a 3-volt lithium battery model CR2032 that gives the internal clock an
service center. To set the clock, access the menu by pressing STOVE and set the day with buttons P1 and P2. Press P7 again to
set the hours, minutes, day, month and year. operation autonomy; battery replacement is necessary if the clock does not keep the time with the stove not
powered, or a series of zeros appears at restart: call an authorized service center.
MENU 03 – Set chrono
To set the clock, access the menu by pressing STOVE and set the day with buttons P1 and P2. Press P7 again to
Allows all time programming functions to be enabled/disabled. To enable the chrono, access the first submenu ENABLE CHRONO
set the hours, minutes, day, month and year.
and set it to ON with buttons P1 or P2. The manual commands from the emergency panel or remote control have priority over
programming. The stove is equipped with three different types of programming: daily, weekly and weekend. Chrono enabling is
signaled by the LEDs shown in the picture below. Daily, weekly and weekend programming is active only if the general chrono is
enabled. Access the second submenu DAY PROGRAM to enable or disable daily programming with buttons P1 and P2.
Then press button P7 and then buttons P1 and P2 to set up to two operation phases delimited by the set times. Access the second
submenu WEEK PROGRAM to enable, disable and set the weekly programming functions. Follow the same procedures of the
previous paragraph. Up to four operation phases delimited by the set times and days can be set.
Carry out programming making sure not to overlap the hours of activation and/or deactivation on the same day
in different programs.
Access the third submenu WEEKEND PROGRAM to enable, disable and set the weekly programming functions for the weekend.
Follow the same procedures of the previous paragraph. Up to two operation phases delimited by the times can be set.
Use and maintenance manual HRB 150 - HRB 200
Stove off
The initial ignition start phase is in progress
Pellet loading in progress during the ignition phase
This is the phase prior to the flame appearing.
The flame has appeared and the stove is in the heating phase
Normal work phase
Power reduced because temp. reached or high fume temp.
Automatic cleaning at regular intervals
Final stove cleaning, before shutdown
Stove off for temperature reached and awaiting request
The stove cannot be relit because awaiting cooling
DESCRIPTION
51 TERMOFIRE L