Pentair Pool Products SEP 100 Guia De Instalacion página 7

1. Turn the pump off, shut off any automatic controls to ensure that the system is not inadvertently started during
servicing.
 2SHQ WKH ¿OWHU +LJK )ORZŒ PDQXDO DLU UHOLHI YDOYH DQG WKH ZDVWH GUDLQ YDOYH RU FDS LI \RXU V\VWHP KDV
one).
3. Remove hair and lint strainer pot lid and clean basket. Replace basket and secure lid.
4. Open the drain valve and wait for the water to drain from the separation tank before removing the bag
containing D.E. and contaminants.
5. Remove locking ring by depressing safety latches on both sides of ring and rotate counterclockwise, then
remove tank lid.
6. Remove the separation bag by pulling straight up on the bag handle loop.
7. Dispose of waste in trash and rinse bag clean. Inspect bag for holes - replace if necessary.
 &OHDQ DQG UHPRYH GHEULV IURP LQVLGH WKH ¿OWHU WDQN DQG IURP WKH 2ULQJ DQG 2ULQJ JURRYH RQ WKH WDQNERG\
9. Install the clean bag into the tank assembly making sure it is seated onto the separation tank ring.
 5HSODFH WKH WDQN OLG RQWR WKH WDQN ERG\ PDNLQJ VXUH LW LV IXOO\ DQG ¿UPO\ VHDWHG RQ WKH WDQN ERG\
11. Place lock ring over tank lid, and centering the lock ring on the threads of the tank body, turn the lock ring
clockwise until the safety latches click and the lock ring hits the stops on the body. DO NOT ATTEMPT TO
29(57,*+7(1 7+( /2&. 5,1* $)7(5 /2&. 5,1* +$6 +,7 7+( 67236 21 7+( %2'<
Any time the separation tank is opened, and/or separation bag is removed, be sure to generously coat the O-
ULQJ ZLWK VLOLFRQH OXEULFDQW EHIRUH UHDVVHPEOLQJ WKH XQLW '2 127 86( 3(752/(80 %$6(' /8%5,&$176
%(&$86( 7+(< +$9( $ '(7(5,25$7,1* ())(&7 21 58%%(5
12. Replace drain cap and reinstall High Flow™ manual air relief valve drain hose if used.
E. CLEANING THE HIGH FLOW™ MANUAL AIR RELIEF
VALVE
1. Turn the pump off and shut off any automatic controls to ensure
that the system is not inadvertently started during servicing.
2. OPEN THE HIGH FLOW™ MANUAL AIR RELIEF VALVE UNTIL
IT SNAPS INTO THE FULL OPEN POSITION, THEN WAIT
UNTIL ALL PRESSURE IS RELIEVED.
 :LWK WKH UHOLHI YDOYH DWWDFKHG WR WKH ¿OWHU WDQN SXOO RXW WKH ORFNLQJ
tabs and remove the valve stem and cover assembly with a
counterclockwise and lifting motion, see Figure 3.
 &OHDQ GHEULV IURP WKH YDOYH VWHP DQG ERG\ 9HULI\ WKDW WKH ¿OWHU
tank's air passage is open by inserting a 5/16 in. drill bit through
the valve body. Verify that the O-ring are in good condition, properly
positioned, and lubricated with a silicone base lubricant.
5. Reinstall the valve stem and cover assembly with a downward and
clockwise motion until it snaps into position.
NOTE
Figure 3.
7