Double Insulation - Narex EV 16 K-2 Instrucciones De Uso

Technická data
Drill / Impact Drill
Type
Supply voltage
Power frequency
Power input
Idle speed
1st speed gear
2nd speed gear
Number of impacts
1st speed gear
2nd speed gear
Maximum torque
1st speed gear
2nd speed gear
Speed pre-selection
Safety clutch
Extent of chuck ø
Thread on spindle
Drilling ø max.
into steel
into wood
into concrete
Clamping neck ø
Weight
Protection class
* Limited by safety clutch
Controls
1 ...........Chuck with ring gear
2 ...........Clamping neck
3 ...........Latching pin
4a .........Switch / controller
4b .........Alteration switch lever
5 ...........Speed pre-selection wheel
6 ...........Air vents
7 ...........Gear-shifting lever
8 ...........Hammer gear button
9 ...........Additional handle
10 .........Stop bar
11 .........Chuck hook
12 .........Spots on spindle
13 .........Socket screw wrench
14 .........Wing screw
15 .........Wing screw
16 .........Wing screw
The displayed or described accessories need not be included in the
delivery package.

Double insulation

To ensure maximum safety of the user, our tools are designed and
built to satisfy applicable European standards (EN standards). Tools
with double insulation are marked by the international symbol of
a double square. These tools must not be grounded and a two-wire
cable is sufficient to supply them with power. Tools are shielded in
accordance with EN 50114.
Use
EV 16 K-2:
The machine is intended drilling in wood, metal, ceramic and plas-
tic. Machines with electronic control and right/left rotation are also
suitable for screwing and thread cutting ( Only for soft screwdriv-
ing applications).
full drill bit
annular bit
EVP 16 K-2:
The machine is intended for impact drilling in brick, concrete and
stone as well as for drilling in wood, metal, ceramics and plastics.
Machines with electronic control and right/left rotation are also
suitable for screwing and thread-cutting.
The user alone is responsible for any liabilities caused by usage
other than intended.
The safety clutch is activated if the drill becomes jammed or
caught.
Any unauthorised use might cause damage to the tool. Therefore
follow these instructions:
Check whether the data on the name plate correspond with the
actual power supply voltage. Tools designed for 230 V may be con-
nected also to 220 / 240 V.
Additional handle
For safety reasons always use the enclosed auxiliary handle (9).
Fasten the auxiliary handle to the clamping collar (2) with the wing
bolt (14).
By loosening the wing bolt (15) the drilling depth can be adjusted
with the depth stop adjustment (10).
The auxiliary handle is used to guide the machine securely, espe-
cially with sudden occuring reaction torque (e. g. jamming of the
drill bit).
By loosening the wing bolt (16) the position of the auxiliary
handle can be adjusted in length direction.
EV 16 K-2
230–240 V
50–60 Hz
1 050 W
0–970 min
-1
0–1 750 min
-1
û
û
62.5 Nm
35 Nm
ü
û
3–16 mm
5/8"-16UN-2A
16 mm
60 mm
û
û
57 mm
3.6 kg
II /
Safety clutch (EVP 16 K-2)
Commissioning and use
- Always use sharp drill bits.
- Load the tool to avoid any significant reduction of speed or
stoppage.
- Always change the speed gear when the machine is idle or at
the machine slow-down at low speed, in no case during the
drilling or when the machine is otherwise loaded.
English
EVP 16 K-2
230–240 V
50–60 Hz
1 050 W
0–970 min
-1
0–1 750 min
-1
0–19 400 min
-1
0–35 000 min
-1
35 Nm*
19.5 Nm*
ü
ü
3–16 mm
5/8"-16UN-2A
16 mm
55 mm
30 mm
55 mm
57 mm
3.8 kg
II /
13