Publicidad
TECHNICAL DATA
Rated input .............................................................................
No-load speed ........................................................................
Saw blade dia. x hole dia .......................................................
Cutting depth at 90° ................................................................
Cutting depth at 45° ................................................................
Weight without cable ..............................................................
Noise/vibration information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound power level (K = 3 dB(A)) ...........................................
Sound pressure level (K = 3 dB(A)) ......................................
Wear ear protectors!
Total vibration values (vector sum in the three axes)
determined according to EN 60745.
Vibration emission value a
.................................................
h
Uncertainty K .......................................................................
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745
and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with
different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running
but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
WARNING! Read all safety warnings and all instructions,
including those given in the accompanying brochure. Failure
to follow the warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Danger: Keep hands away from cutting area and the blade.
Keep your second hand on auxiliary handle, or motor
housing. If both hands are holding the saw, they cannot be cut by
the blade.
Do not reach underneath the workpiece. The guard cannot
protect you from the blade below the workpiece.
Adjust the cutting depth to the thickness of the workpiece.
Less than a full tooth of the blade teeth should be visible below the
workpiece.
Never hold piece being cut in your hands or across your leg.
Secure the workpiece to a stable platform. It is important to
support the work properly to minimize body exposure, blade
binding, or loss of control.
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting tool may contact
hidden wiring or its own cord. Contact with a "live" wire will also
make exposed metal parts of the power tool "live" and shock the
operator.
When ripping always use a rip fence or straight edge guide.
This improves the accuracy of cut and reduces the chance of blade
binding.
Always use blades with correct size and shape (diamond
versus round) of arbour holes. Blades that do not match the
mounting hardware of the saw will run eccentrically, causing loss of
control.
Never use damaged or incorrect blade washers or bolt. The
blade washers and bolt were specially designed for your saw, for
optimum performance and safety of operation.
Causes and operator prevention of kickback:
- kickback is a sudden reaction to a pinched, bound or misaligned
saw blade, causing an uncontrolled saw to lift up and out of the
workpiece toward the operator;
- when the blade is pinched or bound tightly by the kerf closing
down, the blade stalls and the motor reaction drives the unit rapidly
back toward the operator;
- if the blade becomes twisted or misaligned in the cut, the teeth at
the back edge of the blade can dig into the top surface of the wood
26
ENGLISH
220-240 V
110-120 V
.......................1900 W .........................1750 W
.......................6300 min
.....................6300 min
-1
-1
................... 190x30 mm .................. 190x30 mm
........................0-65 mm .......................0-65 mm
........................0-52 mm .......................0-52 mm
..........................5,5 kg ............................5,5 kg
...........................93 dB(A) .......................93 dB(A)
.........................104 dB(A) .....................104 dB(A)
..........................3,1 m/s
........................2,6 m/s
2
2
..........................1,5 m/s
2
........................1,5 m/s
2
causing the blade to climb out of the kerf and jump back toward the
operator.
Kickback is the result of saw misuse and/or incorrect operating
procedures or conditions and can be avoided by taking proper
precautions as given below.
Maintain a firm grip with both hands on the saw and position
your arms to resist kickback forces. Position your body to
either side of the blade, but not in line with the blade. Kickback
could cause the saw to jump backwards, but kickback forces can
be controlled by the operator, if proper precautions are taken.
When blade is binding, or when interrupting a cut for any
reason, release the trigger and hold the saw motionless in the
material until the blade comes to a complete stop. Never
attempt to remove the saw from the work or pull the saw
backward while the blade is in motion or kickback may occur.
Investigate and take corrective actions to eliminate the cause of
blade binding.
When restarting a saw in the workpiece, centre the saw blade
in the kerf and check that saw teeth are not engaged into the
material. If saw blade is binding, it may walk up or kickback from
the workpiece as the saw is restarted.
Support large panels to minimise the risk of blade pinching
and kickback. Large panels tend to sag under their own weight.
Supports must be placed under the panel on both sides, near the
line of cut and near the edge of the panel.
Do not use dull or damaged blades. Unsharpened or improperly
set blades produce narrow kerf causing excessive friction, blade
binding and kickback.
Blade depth and bevel adjusting locking levers must be tight
and secure before making cut. If blade adjustment shifts while
cutting, it may cause binding and kickback.
Use extra caution when making a "plunge cut" into existing
walls or other blind areas. The protruding blade may cut objects
that can cause kickback.
Check lower guard for proper closing before each use. Do not
operate the saw if lower guard does not move freely and close
instantly. Never clamp or tie the lower guard into the open
position. If saw is accidentally dropped, lower guard may be bent.
Raise the lower guard with the retracting handle and make sure it
moves freely and does not touch the blade or any other part, in all
angles and depths of cut.
Check the operation of the lower guard spring. If the guard
and the spring are not operating properly, they must be
serviced before use. Lower guard may operate sluggishly due to
damaged parts, gummy deposits, or a build-up of debris.
Lower guard may be retracted manually only for special cuts
such as "plunge cuts" and "compound cuts." Raise lower
guard by retracting handle and as soon as blade enters the
material, the lower guard must be released. For all other
sawing, the lower guard should operate automatically.
Always observe that the lower guard is covering the blade
before placing saw down on bench or floor. An unprotected,
coasting blade will cause the saw to walk backwards, cutting
whatever is in its path. Be aware of the time it takes for the blade
to stop after switch is released.
Use the appropriate riving knife for the blade being used. For
the riving knife to work, it must be thicker than the body of the
blade but thinner than the tooth set of the blade.
Adjust the riving knife as described in this instruction manual.
Incorrect spacing, positioning and alignment can make the riving
knife ineffective in preventing kickback.
Always use the riving knife except when plunge cutting. Riving
knife must be replaced after plunge cutting. Riving knife causes
interference during plunge cutting and can create kickback.
For the riving knife to work, it must be engaged in the
workpiece. The riving knife is ineffective in preventing kickback
during short cuts.
Do not operate the saw if riving knife is bent. Even a light
interference can slow the closing rate of a guard.
Do not use saw blades not corresponding to the key data given in
these instructions for use.
Wear ear protectors. Exposure to noise can cause hearing loss.
Please do not use abrasion disks in this machine!
Appliances used at many different locations including open air
must be connected via a current surge preventing switch.
Always wear goggles when using the machine. It is recommended
to wear gloves, sturdy non slipping shoes and apron.
Always disconnect the plug from the socket before carrying out any
work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine. Always
lead the cable away behind you.
Before use check machine, cable, and plug for any damages or
material fatigue. Repairs should only be carried out by authorised
Service Agents.
Do not fix the on/off switch in the "on" position when using the saw
hand-held.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Wear a suitable dust protection mask.
SPECIFIED CONDITIONS OF USE
This electronic circular saw can cut lengthways and mitre
accurately in wood, plastic, and aluminium.
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in
conformity with the following standards or standardized
documents. EN 60745, EN 55014-1, EN 55014-2, EN 61000-3-2,
EN 61000-3-11, in accordance with the regulations 98/37/EC,
2004/108/EC
Rainer Kumpf
Winnenden, 2008-03-06
Manager Product Development
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the system
voltage indicated on the rating plate. It is also possible to connect
to sockets without an earthing contact as the design conforms to
safety class II.
Inrush currents cause short-time voltage drops. Under
unfavourable power supply conditions, other equipment may be
affected. If the system impedance of the power supply is lower
than 0,2 Ohm, disturbances are unlikely to occur.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
Use only Milwaukee accessories and Milwaukee spare parts.
Should components need to be replaced which have not been
described, please contact one of our Milwaukee service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the Article No. as well as the machine type printed on the
label and order the drawing at your local service agents or directly
at: Milwaukee Electric Tool, Max-Eyth-Straße 10,
D-71364 Winnenden, Germany.
SYMBOLS
Please read the instructions carefully before
starting the machine.
Always disconnect the plug from the socket before
carrying out any work on the machine.
Accessory - Not included in standard equipment,
available as an accessory.
Do not dispose of electric tools together with
household waste material! In observance of
European Directive 2002/96/EC on waste electrical
and electronic equipment and its implementation in
accordance with national law, electric tools that
have reached the end of their life must be collected
separately and returned to an environmentally
compatible recycling facility.
ENGLISH
27
Publicidad
