Beretta POWER GREEN 50 Manual De Uso E Instalación página 12

faults
When there is an operating fault, the flame symbol
the display and a flashing code will be shown along with the
icons (simultaneously or otherwise).
For a description of the faults, refer to the table below.
fAULT dEScRIPTION
LOCKOUT DUE TO FLAME FAILURE/WATER CIRCULATION FAILURE (D)
PARASITE FLAME (T)
NEW ATTEMPT IN PROGRESS (T)
MINIMUM GAS INPUT PRESSURE (T)
MINIMUM GAS INPUT PRESSURE (D)
LIMIT THERMOSTAT
FLUE GAS PROBE - SHORT CIRCUIT (D)
LIMIT TEMPERATURE DELIVERY PROBE (D)
LIMIT TEMPERATURE DELIVERY PROBE (T)
LIMIT TEMPERATURE RETURN PROBE (D)
LIMIT TEMPERATURE RETURN PROBE (T)
RETURN-DELIVERY PROBE DIFFERENTIAL (D)
FLUE GAS PROBE - OVERTEMPERATURE (D)
FAN (cycle start) (D)
FAN CYCLE IN PROGRESS (high rpm) (D)
INSUFFICIENT SYSTEM PRESSURE (D*)
INSUFFICIENT SYSTEM PRESSURE (T*)
WATER PRESSURE TRANSDUCER (D)
ELECTRONIC CARD (D)
DOMESTIC PROBE (T°)
MINI-ACCUMULATION ALARM THRESHOLD (-)
PRIMARY PROBE SHORT CIRCUIT/OPEN (D)
DELIVERY PROBE OVERTEMPERATURE (T)
RETURN PROBE SHORT CIRCUIT/OPEN (D)
NO HEATING PROBE ON SECOND SYSTEM
LOW TEMPERATURE THERMOSTAT (T)
DELIVERY/RETURN DIFFERENTIAL (T)
DELIVERY/RETURN DIFFERENTIAL (D)
SYSTEM FAULT (D)
SYSTEM FAULT (T)
SYSTEM FAULT (D)
SYSTEM FAULT (T)
PRIMARY HEAT EXCHANGER CLEANING (-)
The temporary visualisation of alarm code 21 during the initial ignition phase (with a flame present) does not indicate a fault. If the alarm remains
however, refer to the table above.
(D) Definitive.
(T) Temporary. In this operating status, the boiler attempts to resolve the fault situation autonomously.
(°) See the NOTE on the next page.
(*) If these two errors arise, check the pressure shown on the hydrometer.
If the pressure is insufficient (< 0.4 bar - red field), perform the filling operations described in the "Filling and draining the systems" chapter.
If the system pressure is sufficient (> 0.6 bar - light blue field), the fault is due to a lack of circulating water. Contact the Technical Assistance Service.
(-) Contact the Technical Assistance Service.
Resetting the faults
Wait about 10 seconds before resetting normal operating conditions,
then proceed as follows:
1) Visualisation of the
The appearance of the
diagnosed, and the boiler is attempting to resolve it autonomously
(temporary stop).
If the boiler does not resume normal operation, the display will show one
of the following three possibilities:
mode A (fig.22)
Disappearance of the , appearance of the
ent alarm code.
In this case, proceed as described in point 2.
mode b (fig.23)
Together with the , the
different alarm code.
In this case, proceed as described in point 3.
mode c
Together with the , alarm code 91 will appear.
The intervention of the Technical Assistance Service is required.
2) Visualisation of the icon only
Press the key to restore operation. If the boiler ignites and resumes
normal operation, the stop can be attributed to a random situation.
If the shutdown reoccurs however, you should contact the Technical
Assistance Service.
12
will disappear from
icon only
indicates that an operating fault has been
icon, and a differ-
icon will also appear, along with a
(fig.24)
and
Alarm
icon
10
11
12
13
14
20
21
24
25
26
27
28
29
34
37
40
41
42
50-59
60
65
70
71
72
75
77
78
79
80
81
82
83
91
temporary fault
temporary fault
code Icon
YES NO
NO YES
NO NO
NO YES
YES NO
YES NO
YES YES
YES NO
NO YES
YES NO
NO YES
YES YES
YES YES
YES NO
YES YES
YES NO
NO YES
YES YES
YES YES
NO YES
NO YES
YES YES
NO NO
YES YES
NO YES
NO YES
NO YES
YES NO
YES YES
NO YES
YES YES
NO YES
NO YES
MOdE A
definitive fault
MOdE b
definitive fault
Fig.22
Fig.23