Maintenance / Disposing; Technical Data - Martin Yale intimus POWER 15.90 S Instrucciones De Uso

GB
Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung
MOTOR FAULT:
If the motor is overloaded, the integrated ther-
mal protection system cuts off the main power
supply. This is indicated by the blinking „Motor
fault" lamp (8).
However, while the motor is cooling down, you
can still operate the machine in inching mode (at
reduced power - Y-connection; e.g. to retrieve
material).
The shredder should only be operated
at reduced power to retrieve material
or to fully shred material already being
processed. Any further operation may
seriously damage the motor.
After the machine has cooled down sufficiently
(about 5-10 minutes), the lamp goes out, and the
machine can again be operated normally (delta
connection).
Note: If the machine still does not return to normal
operation after cooling down (lamp (8) fails to go
out), this means there is a fault in the machine.
If this occurs, please notify our customer service
department.

MAINTENANCE / DISPOSING

CUTTING SYSTEM MAINTANANCE:
After about 8 hours of continuous ope-
ration run the cutting system in reverse
for about 30 seconds and, at the same
time, spray some of the enclosed special
oil onto the cutting system.
GEAR BOX MAINTAINANCE:
Both synchron gears, as well as the chain wheels
and drive chains must be greased monthly.
The machine must be turned off at the
main switch (1) (fig.5) and unplugged
before the machine is opened.
Proceed as follows:
1. Remove the left side cover from the housing.
2. Grease the above mentioned parts with a brush
or a grease gun, and a standard, commercially
available grease.
Description
Plastic bag, 900 x 900 x 1500 x 0,15mm
Lubrication bottle, 125 ml
Note: Please contact your dealer when ordering accessories and replacement parts.
MALFUNCTION
FAULT CHECKLIST:
If the machine is not functioning properly, you
should check the following:
- is the machine plugged into the mains power
supply?
- is the locking switch (2) unlocked?
- is the main switch (1) turned on?
- is the emergency-stop rail (14) released?
Pull out the red rail on the feed table.
- is the shredder bin (23) fully docked?
- is the shredder bin (23) full?
Empty the shredder bin.
- is the switch flap (18) (fig. 3) for the „shredder
bin full" indicator easy to move?
It may be necessary to free the switch.
- is the motor overloaded?
Please refer to the section headed „Motor
Fault".
- is there a phase failure?
Check the three-phase fuse at the power supply
socket, and replace if necessary.
If you still cannot isolate the fault after carrying
out all these checks, please notify our customer
service department.
3. Re-install the side cover and connect the ma-
chine to the mains. The machine can be put
back into operation.
The machine may not be modified in
any way!
Operation of the machine is prohibited
if modifications are undertaken!
ENERGY SAVING TIP:
Be certain that the machine is turned off overnight
(main switch (1) (fig. 5) switched to „0").
DISPOSING OF THE MACHINE:
Dispose
environmentally sound fashion at the
end of its useful service life. Do not
dispose of any of the parts included
in the machine or its packaging with
household trash.
ACCESSORIES
of the machine in an
Order-No.
99960
99943
13
15.90 S/16.50 S
Always unplug the machine from the
mains power supply, turn off the main
switch and lock it with a padlock be-
fore opening the machine to carry out
any repairs.
18
Fig. 3

TECHNICAL DATA

Cutting widths: 11.8 x 55 mm
7.8 x 55 mm
6 x 50 mm
Cutting capacity:
15.90 S:
11.8 x 55 mm: 260-320 sheets (70 g/m
7.8 x 55 mm: 200-260 sheets (70 g/m
6 x 50 mm: 180-210 sheets (70 g/m
16.50 S:
11.8 x 55 mm: 400-550 sheets (70 g/m
7.8 x 55 mm: 350-420 sheets (70 g/m
6 x 50 mm: 300-330 sheets (70 g/m
Supply voltage:
400V/50Hz
230V/50Hz
415V/50Hz
220V/60Hz
200V/50Hz
200V/60Hz
Pre-fusing:
(gl fuse, type 1 assignment)
400V-415V/50Hz: 35 A
220V-230V/50Hz: 40 A
200V/50Hz: 63 A
Working width: 500 mm
Noise level: approx. 74 dB(A)
Power:
15.90 S: 5.5 kW
16.50 S: 7.5 kW
Length:
1950 mm
Width:
1200 mm
Height:
1550 mm
Weight:
15.90 S:
approx. 696 kg
16.50 S:
approx. 726 kg
)
2
)
2
)
2
)
2
)
2
)
2