General Safety Norms - Ryobi ECS 1940 Manual De Instrucciones

4. G
ENERAL SAFETY NORMS
All users of the chain saw must first care-
fully read the maintenance and operating
manual and familiarise themselves fully with
all controls for correct operation of the de-
vice.
Do not let children come into con-
tact with the tool. Keep all the peo-
ple away from the work area
n
Using electric tools, basic safety precau-
tions should always be followed to re-
duce the risk of fire,electric shock and
personal injury.
n
Guard against electic shock. Avoid body
contact with earthed or grounded sur-
faces.
n
Store idle tool. When not in use the tools
should be stored in a dry, hight or locked
up place, out of reach of children.
n
Do not force the tools. It will do the job
better safer at the rate for which it was
intended.
n
Cluttered areas and benches can cause
accident.
n
Read the following safety instruction and
tool's labels before attempting to operate
this product. Be aware of tool's operation
range and limitations as well as its dan-
gers.
n
When not in use, power tools must be
stored in a dry place and locked up se-
curely, out of reach of children.
n
Never allow the chain saw near your
body or your clothing when starting or
using it.
n
Do not switch your machine on when it is
upside down.
n
When starting the chain saw ensure the
chain is not touching anything.
n
Remember that the machine continues to
run for a short period after it is switched
off.
n
Beware of objects hurled by the line
head.
n
Do not use and do not start up and do not
use the chain saw near people, other ani-
mals or obtrusive objects.
n
During operation we recommend keeping
a minimum distance of 10 m between the
machine and other people.
n
Always hold the device with both hands.
n
Stand in a safe and steady position on
both legs.
n
Never carry the chainsaw by the cable or
when it is connected to the mains or with
your fingers on the trigger.
n
Avoid accidental starting. Ensure the
switch is in the off position before
plugging in. Carrying power tools with
your finger on the switch or plugging in
power tools that have the switch on in-
vites accidents.
n
Keep the cable away from heat sources,
oils or sharp edges.
n
When sawing, do not use chainsaw
above shoulder height.
n
The operator is responsible for any acci-
dents or hazards that may occur to other
persons or their belongings.
n
Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from mov-
ing parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
Wear clothing and safety gear suit-
able for chain saw cutters opera-
tions. We suggest wearing:
• safety helmet
• noise-damping earplugs
• protective goggles or visor
• protective gloves
• protective trousers
• sturdy shoes not sliding
Always use an extension cable
with high insulation characteristics
and which meets all current legis-
lation requirements.
n
When operating a power tool out-
doors, use an extension cord suit-
able for outdoor use. Use of a cord
suitable for outdoor use reduces the risk
of electric shock.
n
Before starting the motor, ensure that the
extension cable is clear of the cutting
zone.
n
Any damaged cable must be replaced im-
mediately by authorized staff.
n
Remove the plug from the sacket before
carrying out any adjustment, servicing or
maintenance.
n
For safety reasons, the socket used to
power the unit should be backed up by a
residual current device-operated (FI)
circuitbreaker which can be tripped by a
max. current of 30mA.
n
Check damaged parts. Before further use
of your chainsaw, a guard or other part
that is damaged should be carefully
checked to determine whether it will op-
erate properly and perform its intended
function. Check for alignment of moving
parts, binding of moving parts, breakage
of parts, mounting and any other condi-
tions that may affect its operation.
A guard or other part that is damaged
should be properly repaired or replaced
by an authorised service agent. Do not
use your chainsaw if the switch does not
turn it on and off.
7