Publicidad

Enlaces rápidos

DECLARATION OF CONFORMITY
This product is marked
– Low voltage no. 2006/95/CE.
– Electromagnetic compatibility no. 2004/108/CE, 92/31 EEC and 93/68 EEC.
This declaration will become void in case of misuse and/or non observance though partial of manufacturer's installation
and/or operating instructions.
OPERATING LIMITS
L
Cooling Maximum conditions
Outdoor temperature :
Room temperature :
L
Cooling Minimum conditions
Outdoor temperature :
Room temperature :
L
Heating Maximum conditions
Outdoor temperature :
Room temperature :
L
Heating Minimum conditions
Outdoor temperature :
Room temperature :
F-GAS Regulation (EC) No. 842/2006
Do not vent R410A into atmosphere: R410A is a
fluorinated greenhouse gas, covered by Kyoto Protocol,
with a Global Warming Potential (GWP) = 1975.
Tools required for installation (not supplied)
1.Standard screwdriver
2.Phillips head screwdriver
3.Knife or wire stripper
4.Tape measure
5.Level
6.Sabre saw or key hole saw
7.Hacksaw
8. Core bits ø 5
INSTALLATION INSTRUCTIONS
as it satisfies Directives:
43°C D.B.
32°C D.B. / 23°C W.B.
–15°C D.B.
10°C D.B. / 6°C W.B.
24°C D.B. / 18°C W.B.
27°C D.B.
–15°C D.B.
5°C D.B.
19.Hammer
10.Drill
11. Tube cutter
12.Tube flaring tool
13.Torque wrench
14.Adjustable wrench
15.Reamer (for reburring)
16.Hex. key
37.4255.054.02
- Split system air conditioner -
Model Combinations
Combine indoor and outdoor units only as listed below.
MONO SPLIT
Indoor Units
MPAFIA0R5I--
MONO SPLIT (WITH ADAPTER)
MPA9FIB0R5I-- x 1
MULTI SPLIT
FOR "MULTI SPLIT"
MPAFIA0R5I--
COMBINATIONS SEE
INSTALLATION
MPA9FIB0R5I--
INSTRUCTIONS OF
OUTDOOR UNITS
Power Supply:
220 - 240 V ~ 50 Hz
02/2012
EG
I
F
D
E
Outdoor Units
GRF99R5I--
GRF98R5I--
GRF129R5I--
GRF128R5I--
GR9FI30R5I--
GR9FI50R5I--
GR9FI50R5I--
GR9FI65R5I--
GR9FI80R5I--

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Technibel MONO SPLIT

  • Página 1 GRF129R5I-- GRF128R5I-- Heating Maximum conditions GR9FI30R5I-- Outdoor temperature : 24°C D.B. / 18°C W.B. Room temperature : 27°C D.B. MONO SPLIT (WITH ADAPTER) Heating Minimum conditions MPA9FIB0R5I-- x 1 GR9FI50R5I-- Outdoor temperature : –15°C D.B. Room temperature : 5°C D.B.
  • Página 2: Important

    IMPORTANT! • Ground the unit following local electrical codes. • The Yellow/Green wire cannot be used for any connection Please read before installation different from the ground connection. • Connect all wiring tightly. Loose wiring may cause This air conditioning system meets strict safety and operating overheating at connection points and a possible fire standards.
  • Página 3 (min. thickness 8mm). MODEL NARROW TUBE LARGE TUBE OUTER DIAMETER MIN. THICKNESS OUTER DIAMETER MIN. THICKNESS MONO SPLIT 6,35 mm 0,8 mm 9,52 mm 0,8 mm MULTI SPLIT SEE INSTALLATION INSTRUCTIONS OF OUTDOOR UNIT MPA9 x 1 SEE INSTALLATION INSTRUCTIONS OF OUTDOOR UNIT PVC pipe for condensate drain pipe (ø...
  • Página 4: Dichiarazione Di Conformità

    GRF128R5I-- Condizioni Massime in Riscaldamento GR9FI30R5I-- Temperatura esterna : 24°C B.S. / 18°C B.U. Temperatura interna : 27°C B.S. MONO SPLIT (CON ADATTATORE) Condizioni Minime in Riscaldamento MPA9FIB0R5I-- x 1 GR9FI50R5I-- Temperatura esterna : –15°C B.S. Temperatura interna : 5°C B.S.
  • Página 5: Importante

    IMPORTANTE! • Eseguire la messa a terra dell’unità secondo le norme elettriche locali. Leggere prima di iniziare l’installazione • Il conduttore giallo/verde non può essere utilizzato per collegamenti diversi dalla messa a terra. Questo sistema di condizionamento deve seguire rigidi •...
  • Página 6 MODELLO TUBO PICCOLO TUBO GRANDE DIAMETRO ESTERNO SPESSORE MINIMO DIAMETRO ESTERNO SPESSORE MINIMO MONO SPLIT 6,35 mm 0,8 mm 9,52 mm 0,8 mm MULTI SPLIT V. ISTRUZIONI DI INSTALLAZIONE UNITA' ESTERNA MPA9 x 1 V. ISTRUZIONI DI INSTALLAZIONE UNITA' ESTERNA Tubo in PVC per scarico condensa (ø...
  • Página 7 GRF128R5I-- Conditions maximales en Chauffage Température extérieure : 24°C B.S. / 18°C B.H. GR9FI30R5I-- Température intérieure : 27°C B.S. MONO SPLIT (AVEC ADAPTATEUR) Conditions minimales en Chauffage MPA9FIB0R5I-- x 1 GR9FI50R5I-- Température extérieure : –15°C B.S. Température intérieure : 5°C B.S.
  • Página 8: Veuillez Lire Ce Qui Suit Avant De Commencer

    IMPORTANT! • Effectuez la mise à la terre de l'appareil en respectant les réglementations électriques locales. Veuillez lire ce qui suit avant de commencer • Le câble jaune/vert ne peut en aucun cas être utilisé pour Ce système de conditionnement de l'air répond à des toute autre connexion que celle de la mise à...
  • Página 9 épaisseur min. de 8mm. MODELE PETIT TUBE GROS TUBE DIAMETRE EXTERIEUR EPAISSEUR MIN. DIAMETRE EXTERIEUR EPAISSEUR MIN. MONO SPLIT 6,35 mm 0,8 mm 9,52 mm 0,8 mm MULTI SPLIT V. NOTICE D'INSTALLATION UNITE EXTERIEURE MPA9 x 1 V.
  • Página 10: Konformitätserklärung

    : 10°C T.K. / 6°C F.K. GRF129R5I-- GRF128R5I-- Heizbetrieb bei Maximumbedingungen Außentemperatur : 24°C T.K. / 18°C F.K. GR9FI30R5I-- Raumtemperatur : 27°C T.K. MONO SPLIT (MIT ADAPTER) Heizbetrieb bei Minimumbedingungen MPA9FIB0R5I-- x 1 GR9FI50R5I-- Außentemperatur : –15°C T.K. Raumtemperatur : 5°C T.K. MULTI SPLIT FÜR...
  • Página 11 WICHTIG! Tod verursachen. • Erden Sie das Gerät gemäß den örtlich zutreffenden Bitte vor Arbeitsbeginn lesen Vorschriften. Diese Klimaanlage entspricht strengen Sicherheits- und • Das Gelbe/Grüne Kabel ist für die ausschließliche Betriebsnormen. Verwendung als Erdleitung. • Verbinden Sie Kabel fest miteinander. Lockere Für den Installateur oder Bediener dieser Anlage ist es Verbindungen können...
  • Página 12 MODELL ENGES ROHR WEITES ROHR AUßENDURCHMESSER MIN. DICKE AUßENDURCHMESSER MIN. DICKE MONO SPLIT 6,35 mm 0,8 mm 9,52 mm 0,8 mm MULTI SPLIT SEHEN SIE INSTALLATIONSANLEITUNGEN VON AUSSENEINHEIT MPA9 x 1 SEHEN SIE INSTALLATIONSANLEITUNGEN VON AUSSENEINHEIT PVC-Rohr für Kondenswasser-Auslaß (Innen ø 18mm). Es soll lang genug sein, um das Kondenswasser zu einer ●...
  • Página 13: Acondicionador De Aire Split System

    GRF128R5I-- Condiciones Máximas en Calefacción Temperatura exterior : 24°C B.S. / 18°C B.H. GR9FI30R5I-- Temperatura interior : 27°C B.S. MONO SPLIT (CON ADAPTADOR) MPA9FIB0R5I-- x 1 GR9FI50R5I-- Condiciones Mínimas en Calefacción Temperatura exterior : –15°C B.S. MULTI SPLIT Temperatura interior : 5°C B.S.
  • Página 14: Precauciones Especiales

    ¡IMPORTANTE! • Realizar la puesta a tierra de la unidad siguiendo las normas eléctricas locales. Leer antes de empezar la instalación • El conductor amarillo/verde no se puede utilizar para conexiones que no sean la de tierra. Este sistema de acondicionamiento cumple medidas rígidas •...
  • Página 15: Material Adicional Para La Instalacion (No Suministrado)

    MODELO TUBO PEQUEÑO TUBO GRANDE DIAMETRO EXTERIOR ESPESOR MINIMO DIAMETRO EXTERIOR ESPESOR MINIMO MONO SPLIT 6,35 mm 0,8 mm 9,52 mm 0,8 mm MULTI SPLIT VER INSTRUCCIONES DE INSTALACIÓN DE LA UNIDAD EXTERIOR MPA9 x 1 VER INSTRUCCIONES DE INSTALACIÓN DE LA UNIDAD EXTERIOR Tubo de PVC para descarga de condensación (ø...
  • Página 16 INDOOR UNIT • UNITÀ INTERNA • UNITE INTERIEURE • INNENEINHEIT • UNIDAD INTERIOR Minimum operation and maintenance area. Area minima di esercizio e manutenzione. Surface minimum de fonctionnement et d’entretien. Raumbedarf des Gerätes . Area mínima de funcionamiento y manutención. 2000 1110 Remove and discard the set screw on the rear panel.
  • Página 17 Tubing connections from the rear. Use the rear panel as a template. Check the horizontal position with the level. Mark the holes to be made. Collegamento tubi posteriore. Utilizzare il pannello posteriore come dima, mettere a livello, evidenziare i fori da eseguire. Sortie arrière des tubes.
  • Página 18 Use the screws to fix the rear panel to the wall. Make sure the panel is flush against the wall. Any space between the wall and unit will cause noise and vibration. Usando le viti, fissare il pannello posteriore al muro. Assicurarsi che l’unità...
  • Página 19 To fix the front panel again, insert it in the lower side of the unit and align it with the blocking points. Then push lightly on the shown marks. Per rimontare il pannello frontale inserirlo nella parte bassa dell’unità, allinearlo sui punti di bloccaggio, applicare una leggera pressione sui punti indicati.
  • Página 20: Salida Posterior Derecha De Los Tubos

    Running power wires plus ground wire from indoor to outdoor unit (see tab. for size of wires). Stendere un cavo multipolare con filo di terra tra le due unità (vedere tabella per la sezione dei fili). Passer les fils electriques et un fil de terre, entre les deux unités (voir tableau pour la section des fils).
  • Página 21 LEFT REAR TUBING Insert the tubes connecting the units from the outside, then bend them right and remove the inferior removable part of the frame. Hang up the unit and extend the support on the back of indoor unit to make the connection easier.
  • Página 22 Die Leitungen für die Klemmbrett-Verbindung vorbereiten und sie verbinden. (Sieh elektrische Angaben). WARNUNG Stellen Sie sich sicher, daß alle Kabelverbindungen fest sind. Lose Kabel können zur Überhitzung des Anschlüsses oder Fehlfunktion des Gerätes führen. Feuergefahr mag ebenfalls bestehen. Preparar los hilos eléctricos para la conexión con la regleta de bornes y conectarlos (Véase el esquema para la conexión).
  • Página 23 Fill the tube and verify that the condensate can flow correctly. Reassemble the grille according to “L”. Riempire la tubazione quindi verificare il corretto scarico della condensa e rimontare la griglia come al punto L. Remplir le bac et vérifier que la sortie des condensat soit correcte. Remonter la grille selon “L”.
  • Página 24 OUTDOOR UNIT • UNITÀ ESTERNA • UNITE EXTERIEUR • AUßENEINHEIT • UNIDAD EXTERIOR MONO SPLIT Minimum operation and maintenance area Area minima di esercizio e manutenzione. Surface minimum de fonctionnement d’entretien. Raumbedarf des Gerätes. Area mínima de funcionamiento y manutención.
  • Página 25 Use insulated copper tube. Cut approximate 30-50 cm longer than actual distance between units. min. 8 mm min. 8 mm Utilizzare del tubo in rame isolato. Tagliare con lunghezza maggiorata di 30-50 cm oltre la distanza tra le unità. Utiliser de tube en cuivre isolé. Couper à une longueur de 30-50 cm en plus de la distance entre les unités.
  • Página 26 Lubricate Para obtener un buen abocardado hay que cumplir con las siguientes características: - superficie interior lisa y pulida - borde exterior uniforme y liso - tavellanadura cónica de longitud uniforme. Lubricar con aceite anticongelante las superficies de contacto, luego atornillar a mano.
  • Página 27 Remove caps from service valves of both tubes. Then start vacuum pump and let it run for the time indicated in the table (vacuum 10 mm Hg abs.). Rimuovere i cappucci delle valvole di entrambi i tubi. Quindi avviare la pompa del vuoto per un tempo consigliato come da tabella (vuoto di 10 High pressure mm Hg assoluti).
  • Página 28 Turn the service valves stem in counterclockwise to fully open the valves. At this point vacuum pump flexible hose can be disconnected. Replace bonnet and flare nut, tighten them to 200 kg/cm with a torque wrench. Aprire completamente le valvole di servizio (senso antiorario). A questo punto scollegare il flessibile della pompa del vuoto.
  • Página 29 The service port on the wide tube service valve uses a Schrader core valve to access the refrigerant system. Therefore, be sure to use a hose connector which has a push-pin inside. La valvola di servizio del rubinetto dell'unità esterna da utilizzare per il vuoto del sistema, il ripristino carica refrigerante e la misurazione della pressione di esercizio è...
  • Página 30 SYSTEM WIRING DIAGRAM • COLLEGAMENTI ELETTRICI DEL SISTEMA • BRANCHEMENTS ELECTRIQUES DU SYSTEME • ELEKTRISCHE ANSCHLÜSSE DES SYSTEMS • CONEXIONES ELECTRICAS DEL SISTEMA MONO SPLIT DELAYED FUSE FUSIBILE RITARDATO FUSIBLE RETARDE TRÄGE SICHERUNG FUSIBLE DE ACCION RETARDADA Main switch for disconnection from the supply line must have a contact separation in all poles that provides full disconnection under category III overvoltage conditions.
  • Página 31: Longitud, Seccion De Cables Y Fusibles De Accion Retardada

    • LONGITUD, SECCION DE CABLES Y FUSIBLES DE ACCION RETARDADA MODEL L ( m ) S ( mm L ( m ) S ( mm MONO SPLIT 10 A MULTI SPLIT SEE INSTALLATION INSTRUCTIONS OF OUTDOOR UNIT MPA9 x 1 SEE INSTALLATION INSTRUCTIONS OF OUTDOOR UNIT Power supply wire A: Multipolar electric wire;...
  • Página 32 REMOTE CONTROL UNIT INSTALLATION • POSIZIONE DI INSTALLAZIONE TELECOMANDO • EMPLACEMENT DE LA COMMANDE A DISTANCE • POSITION DER FERNBEDIENUNG • POSICION DE INSTALACION DEL MANDO A DISTANCIA REMOTE CONTROL UNIT INSTALLATION To ensure that the air conditioner operates correctly, DO NOT install the remote control unit in the following places: •...
  • Página 33 WALL-MOUNTED POSITION • Momentarily place the remote control unit in the desired mounting position. • Verify that the remote control unit can operate from this position. • Fix the support at the wall with two screws and hang the remote control unit. POSIZIONE A PARETE •...
  • Página 34 SYSTEM POWER SETTING - IMPOSTAZIONE POTENZA DEL SISTEMA - REGLAGE PUISSANCE DU SISTEME - EINSTELLUNG DER KRAFT DES SYSTEMS - REGULACION DE LA FUERZA DEL SISTEMA MULTISPLIT This unit belongs to the iSeries Full DC Inverter, a technology developed by Argo that is able to program a lot of operation parameters directly on the unit, simply through a selection on the remote control during installation: “big room or little room".
  • Página 35: Procedimiento

    Diese Einheit gehört zu iSeries Full DC Inverter, eine von Argo entwickelte Technologie, daß viele Betriebsweise der Elektronik, während der Installation, sofort in der Einheit mit der Fernbedienung einstellen kann: “großes Zimmer oder kleines Zimmer”. Folglich arbeitet die Einheit auf geeigneter Weise gemäß...
  • Página 36 PUMP DOWN Pump down means collecting all refrigerant gas in the Das bedeutet: das Kühlmittel in die Außeneinheit ohne Gas-Verlust zurückzugewinnen. Man benutzt es, wenn system back into the outdoor unit without losing gas. das Klimagerät in eine neue Position gestellt werden Pump down is used when the unit is to be moved of muß...
  • Página 37 Remove the valve manifold. At that time, PUMP DOWN has been completed and all refrigerant gas will have been collected in the outdoor unit. Rimuovere il gruppo manometrico. A questo punto l'operazione di PUMP DOWN è completa poiché tutto il gas refrigerante è raccolto nell'unità esterna.
  • Página 38 In order to carry on a constant improvement, our products can be modified without prior notice. Per garantire un costante miglioramento dei nostri prodotti, ci riserviamo di modificarli senza preavviso. Par souci d’amélioration constante, nos produits peuvent être modifiés sans préavis. Unsere Produkte werden laufend verbessert und können Vorankündigung abgeändert Werden.

Este manual también es adecuado para:

Multi splitMpa9 x 1

Tabla de contenido