Mackie PPM608 Guia De Inicio Rapido página 9

Front & Rear Panel Descriptions –
1. 48V Phantom Power Switch
jacks simultaneously.
2. XLR Inputs
Connect a balanced mic signal using an XLR
connector.
3. Line Inputs
Connect a balanced or unbalanced line-level signal
using a 1/4" connector.
4. Insert
Connect a serial effects processor, such as a compressor
or gate, using a 1/4" Y cable.
5. Compressor
Reduces the dynamic range of input signals.
6. Line/Hi-Z Switch
Engage the switch to play a guitar without
using a DI Box.
7. RCA Inputs
Input for an MP3 player or other music source.
8. Gain
Adjusts the mic/line input sensitivity.
9. Gain Switch
Adjusts the channel's input sensitivity to
optimize for louder [low, engaged] or quieter [high, disengaged]
instrumentation.
10. Low Cut Switch
Cuts bass frequencies below 100 Hz at a slope
of 18 dB per octave.
11. Equalization
Boost or cut the level at certain frequencies
to enhance the sound.
12. Pan
Adjusts how much of the signal is sent to the left
and right outputs.
13. Mute Switch and LED
Mutes the channel signal. The LED
illuminates when the mute switch is engaged.
14. Channel Fader
Adjusts the level to the main mix.
15. Solo Switch
Allows you to listen to individual channels
singly or in combination with other soloed signals. The rude
solo LED flashes when solo switches are engaged.
16. Main Insert
Connect effects processor(s) using a 1/4" Y cable
to the main mix output.
17. Main Out L/R
Connect to the inputs of amplifiers, powered
speakers, or a serial effects processor.
18. Main Mix
Adjusts the level of the signal sent to the main
outputs.
19. Phones
Connect stereo headphones here.
20. Phones Level
Controls the headphones level.
21. 100 Hz Rumble Reduction Switch
low-end.
22. Precision Passive EQ Switch
low-frequency response in passive speakers when engaged.
23. Power Amp Limiter LEDs
Illuminates when the limiter
is activated.
Provides 48V, affecting all XLR
Engage to reduce excess
Enhances clarity and
EN ES FR DE
24. Tape Inputs / Outputs
RCA inputs allow you to connect
a line-level source. RCA outputs allow you to record the main
stereo mix.
25. Tape Level
Controls the input level of a source connected
to the tape inputs.
26. Stereo Graphic EQ
Boost or cut the level at certain frequencies
to enhance the sound of the main mix / monitor output.
27. Main Mix / Mon 2 Switch
for the main mix or monitor 2 bus.
28. Power Amp Inputs
Connect a balanced or unbalanced
line-level signal using a 1/4" connector. This signal is routed
directly to the powered outputs.
29. Break Switch and LED
Mutes all channel inputs, but allows
tape inputs to pass out of the main outs. The LED illuminates when
the break switch is engaged.
30. Main Meters
Used to gauge the soloed input or output levels
to ensure that the signals are not clipping.
31. Aux Mon, Mon Send & Master
the mon send jacks. Each channel has its own level control and
the master adjusts the overall output level.
32. Aux FX, FX Send & Master
or an external processor via the FX send jack. Each channel
has its own level control and the FX master adjusts the overall
level sent out to the internal FX and FX outputs.
33. Preset Selector and Display, Int FX Mute Switch and LED
Turn the preset selector to choose an effect. The display shows
the number of the currently selected effects preset. Engage the
int FX mute to mute the internal effects processor and illuminate
the adjacent mute LED.
34. FX Footswitch
Connect a footswitch to mute or un-mute
the internal effects.
35. Internal FX Routing
Route the effects output to the monitors
and mains independently.
36. FX Return Inputs
Connect the stereo processed outputs
of an effects processor to these 1/4" TRS jacks.
37. LPF (Low Pass Filter)
Engage to add a variable low pass filter
to the line-level mono output. Turn knob to desired frequency
(75 Hz – 200 Hz).
38. FX Return Fader
Adjusts the level of the stereo output
from the internal FX processor being added to the main mix.
39. Power Connector & Switch
cord to this IEC jack. The power switch turns the mixer on and off.
40. Speaker Outputs
Speakon® / 1/4" TS outputs for connecting
passive speakers.
41. Power Amp Mode Switch
the mixer are routed to the internal power amps.
Choose if the GEQ is used
Feed stage monitors via
Feeds the internal FX
Connect the supplied AC power
Determines which signal paths from
Quick Start Guide
9