Operating The Blower; General Maintenance; Spark Arrestor - Ryobi RBL30BPT Manual De Utilización

EN
FR DE ES IT PT
PRIME - Press the primer bulb 7 times.
■
SET the start lever to the START position.
■
PULL the recoil starter until the engine starts.
■
Wait 6-10 seconds, then push the throttle to run.
■
NOTE: Engaging and releasing the throttle releases the start
lever to the RUN position.
To start a warm engine:
PULL the recoil starter until the engine starts.
■
To stop the engine:
Press and hold the switch in the stop "O" position
■
until the engine stops.
WARNING
Keep away from all hot surfaces of the blower.
Failure to do so could result in possible serious
personal injury.

OPERATING THE BLOWER

See Figure 12.
Slip arm through harness strap and onto shoulder,
■
then repeat for the other shoulder. Adjust the straps
to a comfortable position. Refer to Adjusting
Harness Straps earlier in this manual. Remove unit
for starting.
Start the blower. Refer to Starting and Stopping
■
earlier in this manual.
Put on the blower again. The unit should be operated
■
on the operator's right side as shown.
To keep from scattering debris, blow around the
■
outer edges of a debris pile. Never blow directly into
the center of a pile.
Operate power equipment at reasonable hours only
■
— not early in the morning or late at night when
people might be disturbed. Comply with the times
listed in local ordinances.
To reduce sound levels, limit the number of pieces of
■
equipment used at any one time.
Operate blower at the lowest possible throttle speed
■
to do the job.
Check your equipment before operation, especially
■
the muffler, air intakes, and air filters.
Use rakes and brooms to loosen debris before
■
blowing. In dusty conditions, slightly dampen
surfaces when water is available.
Conserve water by using power blowers instead
■
of hoses for many lawn and garden applications,
including areas such as gutters, screens, patios,
RBL30BPT V1.indd 15 RBL30BPT V1.indd 15
NL SV DA NO FI EL HU CS RU
English
■
■
■

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
LUBRICATION
All of the bearings in this tool are lubricated with a
sufficient amount of high grade lubricant for the life of
the unit under normal operating conditions. Therefore,
no further lubrication is required.

SPARK ARRESTOR

The muffler is equipped with a spark arrestor screen
inside muffler body. After extended use the screen can
become dirty and may need to have the muffler replaced
by an authorized servicing dealer.
15
RO PL SL HR TR
grills, porches, and gardens.
Watch out for children, pets, open windows, or freshly
washed cars, and blow debris safely away.
Use the wide sweeper nozzle for larger volume, so
the air stream can work close to the ground.
After using blowers or other equipment, CLEAN UP!
Dispose of debris properly.
Caution
Do not place blower on top of or near loose
debris. Debris may be sucked into blower intake
vent resulting in possible damage to the unit.
MAINTENANCE
WARNING
When servicing, use only identical Ryobi
replacement parts. Use of any other parts may
create a hazard or cause product damage
WARNING
Always wear safety goggles or safety glasses
with side shields during power tool operation
or when blowing dust. If operation is dusty,
also wear a dust mask.
WARNING
Do not at any time let brake fluids, gasoline,
petroleumbased products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may
result in serious personal injury.
ET LT LV SK BG
5/14/09 8:41:39 AM 5/14/09 8:41:39 AM