Additional Safety Rules - Dremel 1800 Manual De Instrucciones

that a careless fraction of a second is sufficient to inflict
severe injury.
Do not alter or misuse tool. Any alteration or modification is
a misuse and may result in serious personal injury.
When using the steel saws, cutoff wheels, high-speed
cutters or tungsten carbide cutters, always have the
work securely clamped. Never attempt to hold the work

Additional Safety Rules

Tool Use
DON'T FORCE TOOL
It will do the job better and safer at the rate for which it was
designed.
USE THE RIGHT TOOL
Don't force a small tool or attachment to do the job of a heavy
duty tool. Don't use tool for purpose not intended—for exam-
ple, don't use a circular saw for cutting tree limbs or logs.
SECURE WORK
Use clamps or a vise to hold work when practical. It's safer
than using your hand and it frees both hands to operate the
tool.
NEVER LEAVE TOOL RUNNING UNATTENDED
Turn power off. Don't leave tool until it comes to a complete
stop.
Tool Care
DO NOT ALTER OR MISUSE TOOL
These tools are precision built. Any alteration or modification
not specified is misuse and may result in dangerous condi-
tions.
AVOID GASEOUS AREAS
Do not operate electric tools in a gaseous or explosive atmo-
sphere. Motors in these tools normally spark, and may result
in a dangerous condition.
MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for better and safer performance.
Follow instructions for lubricating and changing accessories.
Inspect tool cords periodically and if damaged, have repaired
by authorized service facility. Inspect extension cords period-
ically and replace if damaged. Keep handles dry, clean and
free from oil and grease.
Before connecting the tool to a power source (receptacle, out-
let, etc.), be sure voltage supplied is the same as that speci-
fied on the nameplate of the tool. A power source with a volt-
age greater than that specified for the tool can result in serious
injury to the user, as well as damage to the tool. If in doubt, DO
NOT PLUG IN THE TOOL. Using a power source with a volt-
age less than the nameplate rating is harmful to the motor.
with one hand while using any of these accessories. The
reason is that these wheels will grab if they become slightly
canted in the groove, and can kickback, causing loss of con-
trol resulting in serious injury. Your second hand should be
used to steady and guide the hand holding the tool. When a
cutoff wheel grabs, the wheel itself usually breaks. When the
steel saw, high-speed cutters or tungsten carbide cutter grab,
it may jump from the groove and you could lose control of the
tool.
For your own safety, do not operate your Scroll Station until
it is completely assembled and installed according to the
instructions...and until you have read and understood the fol-
lowing:
1. General Safety Rules ........................................................2
2. Motor Specifications and
Electrical Requirements ..................................................7
3. Getting to Know Your Scroll Station ......................9 - 10
4. Operation ..................................................................14 - 16
5. Maintaining Your Scroll Station ....................................19
STABILITY OF SAW
Your Scroll Station must be bolted securely to a stand or
workbench. In addition, if there is any tendency for the Scroll
Station to tip over or move during certain operations, such as
cutting long, heavy boards, bolt your Scroll Station stand or
workbench to the floor.
LOCATION
This Scroll Station is intended for indoor use only.
PROTECTION: Eyes, hands, face, ears and body.
TO AVOID BEING PULLED INTO THE
WARNING
!
BLADE—
DO NOT WEAR:
• Loose Fitting Gloves
• Necktie
• Loose Clothing
• Jewelry
DO:
• Tie Back Long Hair
• Roll Long Sleeves Above Elbow
a. If any part of your saw is missing, malfunctioning, has
been damaged or broken . . . such as the motor switch, or
other operating control, a safety device or the power
cord...cease operating immediately until the particular part
is properly repaired or replaced.
b. Do not cut piece too small to hold by hand.
HINT: When making a very small cut out, always secure
the workpiece to a scrap piece of plywood with double-
faced tape. This way, the work is supported and your fin-
gers are away from the blade.
c. Never turn your Scroll Station on before clearing the table
of all objects (tools, scraps of wood, etc.) except for the
workpiece and related feed or support devices for the
operation planned.
5