Stanley Bostitch GF28WW Instrucciones De Seguridad Y Empleo página 6

●
In observance of European Directives
2002/96/EC & 2006//66/EC on waste
electrical
equipment/batteries and their national
implementations, electric tools/batteries that have
reached the end of their life must be collected
separately and returned to an approved recycling
facility.
● Respect your Bostitch tool as a tool. It is not a toy.
No Horseplay.
● Use the Stanley Bostitch gas framing nailer and gas
concrete nailer only for the purpose for which it was
designed, such as: framing, stud walls, sub flooring
and nailing wood to concrete (GNC40T only). The
GF28WW/GF33PT tools should not be used for
anything other than wood to wood applications.
● Do not drive a nail on another nail.
● Do not drive a nail on metal parts.
● Never use the tool in a manner that could cause a
fastener to be directed towards the user or others in
the work area.
● Do not use the tool as a hammer.
● Always carry the tool by the handle. Never carry the
tool with the trigger pulled.
● Do not alter or modify this tool from the original
design or function without the written approval of
Stanley Bostitch.
● Always be aware that misuse and improper
handling of this tool can cause injury to yourself and
others.
● Never clamp or tape the trigger or safety trip in an
actuated position.
● Never leave a tool unattended with a fuel cell or
battery in place.
● Do not operate this tool if it does not contain a
legible WARNING LABEL.
● Do not continue to use a tool that does not function
properly. Notify your nearest Stanley Bostitch
representative if your tool continues to experience
functional problems.
● During operation, hold the tool in such a way that no
injuries can be caused to the head or to the body
should the tool recoil increase due to variations in
the gas supply or hard areas within the work piece.
● Do not work close to corners or at the edge of the
work piece. The fastener could slip out of the work
piece, possibly causing injury.
and electronic
● When transporting the tool, remove the fuel cell and
battery.
● Check that the safety trip (if present) and the trigger
both function correctly before use.
● Do not dismantle or block any part of the tool,
particularly the safety trip.
● Never perform "emergency repairs" without the
proper equipment.
● Avoid weakening the tool by punching or engraving.
● This power tool is powered by an internal
combustion device. This power tool should only be
used with dispensers of combustible gas which are
listed in these handling instructions.
● Never let the tool be used by children or people who
do not know enough to be able to handle it correctly.
● Keep the right parts in the right places. Do not
remove any of the covers or screws. Keep them in
place as they have their functions. Moreover, never
make modifications to the tool or use it after making
any modifications.
● Check the tool before use. Before using the tool,
always check that no parts are broken, that all
screws are completely tight, and that no parts are
missing or rusty.
● Excessive work could cause accidents. Do not make
tools and accessories work beyond their abilities.
Excessive work not only damages the power tool
but also is dangerous in itself.
● Stop operation immediately if you notice
abnormalities or if the power tool does not work
properly; have the power tool inspected and
serviced.
● Take good care of the tool to ensure its long life.
Always take good care of the power tool and keep
it clean.
● Inspection at regular intervals is essential for safety.
Inspect the power tool at regular intervals so that
the tool can be operated safety and efficiently at all
times.
● Avoid dangerous environments. Do not expose the
power tools or charger to rain and do not use the
power tool and charger in damp or wet conditions.
Keep the work area well lit. Never use power tools
and charger near flammable or explosive materials.
Do not use the tool and charger in the presence of
flammable liquids or gases.
● Store the tool and charger in an idle state. When not
in use, the tool and charger should be stored in a