Listening To The Demo Songs; Restoring The Factory Settings; Specifications (General) - Korg KROSS Serie Manual Del Usuario

2.
Select the function Save All
Press the FUNCTION button. Use the PAGE+ ( ) or PAGE- () but-
tons to select Save All, and then press the MENU (OK) button.
3.
Assign a name to the file, and save it
Press the MENU (OK) button to save the data.
Note: To assign a name to the file that will be saved, press the ENTER button
and enter a name in the text edit dialog box that appears.
Saving a song
Select and execute the function Save SEQ. The rest of the procedure is the same.
See "Saving songs and sounds together", above.

Listening to the demo songs

This procedure loads program and combination data and demo song data
into the KROSS. This means that any edited or newly created favorite
data will be overwritten, and your data will be lost. If you want to keep
this data, save it on an SD card (commercially available). (See "Saving
songs and sounds together")
1.
In global mode, select the page to load
Hold down the EXIT button and press the SEQ button to enter global/media
mode. Access the GLOBAL > BASIC page (if something other than the
BASIC page is shown, press the EXIT button).
2.
Load the demo songs and preload programs
Press the FUNCTION button. Use the PAGE+ () or PAGE- () buttons
to select Load Preload/Demo Data, and then press the MENU (OK) but-
ton. In the Kind field of the dialog box, select All (Preload PCG and
Demo Songs).
Press the MENU (OK) button. A confirmation message appears; once
again press the MENU (OK) button. Loading is executed.
Never turn off the power while data is being loaded.
3.
Press the SEQ button to enter sequencer mode
Access the SEQ > MAIN page (if this is not shown, press the EXIT button).
4.
Use Song Select to select a demo song
Use cursor buttons , , ,  to select the parameter, and use the
VALUE dial etc. to make your selection.
Song Select
5.
Start and stop playback
Press the SEQUENCER (Start/Stop) button to start playback.
Playback stops automatically when the performance is over. To stop mid-
way through the performance, press the
again.
The loaded demo song disappears when the power is turned off; reload it
if necessary.

Restoring the factory settings

This operation returns the preload data for programs, combinations, drum kits,
and user arpeggio patterns, as well as the global settings, to their factory-set
state.
As described in steps 1 and 2 of "Recording on the MIDI sequencer", set the
Kind parameter of the dialog box to All Preload PCG, and execute the load
operation.

Specifications (general)

System:
EDS-i (Enhanced Definition Synthesis - integrated)
Keyboard section:
KROSS2-61: 61-note (velocity sensitive, aftertouch not supported)
KROSS2-88: 88-note NH keyboard (natural weighted hammer action, velocity sensitive,
aftertouch not supported)
Maximum polyphony:
120 voices (120 oscillators)
Preset PCM memory:
Approximately 128 MB (*when converted to 48 kHz 16-bit linear PCM)
Expansion PCM memory:
Approximately 128MB (*when converted to 48 kHz 16-bit linear PCM, for keyboard perfor-
mance)
Sounds:
896 combinations (384 preload, 512 user)
1545 programs (768 preload, 512 user (4 user banks), 265 preset)
Favorites:
128 (16 favorites x 8 banks)
Drum kits:
67 (42 preload, 9 preset, 16 user)
Effects:
134 types, 5 insert effects, 2 master effects
Recorders:
16-track MIDI sequencer,
audio recorder (audio format: PCM audio format, stereo 48 kHz/16-bit)
Pad sampler:
16 pads, stereo 48 kHz/16-bit, WAVE file import is supported
Control inputs/outputs:
DAMPER (half damper is supported), ASSIGNABLE SWITCH,
ASSIGNABLE PEDAL
MIDI IN, MIDI OUT, USB (TYPE B) USB-MIDI interface
Audio outputs:
AUDIO OUTPUT L/MONO, R: ø6.3mm phone jack (TS unbalanced)
Headphone output: ø3.5mm stereo mini-phone jack
USB (TYPE B): USB-AUDIO interface (stereo out)
Audio inputs:
LINE IN: ø3.5mm stereo mini-phone jack
MIC IN: ø6.3mm phone jack (TS unbalanced)
Phantom power and plug-in power are not supported
USB (TYPE B): USB-AUDIO interface (stereo in)
Power supply:
AC adapter connector (DC 9V,
Six AA alkaline or nickel-metal hydride batteries
Battery service life:
Six AA alkaline batteries approximately six hours
Six AA nickel-metal hydride batteries (1900 mAh) approximately seven hours
* With the default settings. Service life varies depending on the batteries used and on
SD cards that can be used:
SD memory cards up to 2 GB
SDHC memory cards up to 32 GB
(Start/Stop) button once
(SDXC memory cards are not supported)
Dimensions (width x depth x height):
KROSS2-61: 935 x 269 x 88 mm / 36.81" x 10.59" x 3.46"
KROSS2-88: 1,448 x 383 x 136 mm / 57.01" x 15.08" x 5.35"
Weight:
KROSS2-61: 3.8 kg / 8.38lbs.
KROSS2-88: 12.3 kg / 27.12lbs.
Power consumption:
5W
Included items:
AC adapter, KROSS Quick Start Guide (this document)
Options:
XVP-20, XVP-10: expression/volume pedal, EXP-2: foot controller, DS-1H: damper pedal,
PS-1, PS-3: pedal switches
* Specifications and appearance are subject to change without notice for
)
the conditions of use.
improvement.
En-9