Cables And Flexible Leaders; Tools And Replacement Blades; Machine Assembly; Instructions For Installing Handles - RIDGID K-6200 Manual Del Operador

K-6200 Drain Cleaning Machine
Cables and Flexible Trap Leaders
Catalog Model
No. No.
92460 C-25
92465 C-26
92470 C-27
43647 C-24
5 / " (16mm)
8
32737 C-27HC
58192 C-24HC
5 / " (16mm)
8
95762 C-25 IW
95757 C-26 IW
95752 C-27 IW
5 / " IW (16mm)
95747 C-24 IW
8
92555 T-458
44122 —
Tools and Replacement Blades — Fits C-24,
C-25, C-26, C-27,C-24 IW, C25 IW, C-26 IW,
C-27 IW, C-24HC, C-27HC
Model
Catalog
No. No. Description
92485 T-403 P-Trap Cutter, 3"
92490 T-404 P-Trap Cutter, 3
92495 T-406 Spear Blade
92500 T-407 Retrieving Auger
92505 T-408 Sawtooth Cutter
51762 T-409 H-D Bulb Auger
92510 T-411 Double Cutter, 2"
92515 T-412 Double Cutter, 2
92520 T-413 Double Cutter, 3"
92525 T-414 Double Cutter, 4"
92530 T-416 Double Cutter, 6"
92535 T-432 3-Blade Cutter, 2"
92540 T-433 3-Blade Cutter, 3"
92545 T-434 3-Blade Cutter, 4"
92550 T-436 3-Blade Cutter, 6"
Blade
Blade
Holder
Coupling*
Figure 2 – Tool Assembly
Description
25' I.C. Cable (7,6m)
50' I.C. Cable (15,2m)
75' I.C. Cable (22,9m)
100' I.C. Cable (30,5m)
75' Hollow-Core (22,9m)
100' Hollow-Core (30,5m)
25' I.W. Cable (7,6m)
50' I.W. Cable (15,2m)
75' I.W. Cable (22,9m)
100' I.W. Cable (30,5m)
5 / " x 2' Leader
8
5 / " Pigtail
8
Replacement
Blade(s) Holder*
92835 92900
1 / " 92840 92900
2
92850 92915
— —
92890 92915
— —
92815 92905
1 / 92820 92905
"
2
92825 92910
92830 92910
92855 92910
92860 92895
92865 92895
92870 92895
92875 92895
Fastener*
* Identifies components
included with holder
Ridge Tool Company

Machine Assembly

WARNING
To prevent serious injury, proper assembly of the
Drain Cleaner is required. The following procedures
should be followed:

Instructions For Installing Handles

Remove the two (2) screws from handle. Loosen two (2)
"T" handles and slide handle into the frame (Figure 5).
Replace the two screws in the handle to prevent it slid-
ing out of the frame. Adjust the handle to the desired
height and firmly tighten the "T" handles to lock the
handle in place.

Instructions For Installing Cable

Do not remove bands or staples from cable
CAUTION
shipping carton. Cable is under tension and will whip,
causing injury.
Retrieve end of cable through the center hole of carton and
remove enough cable to connect with drum pigtail. Connect
to pigtail by sliding cable couplings together and turning
screwdriver slot in coupler 180°. Couplings are in locked
position when hash mark is on opposite side of screwdriver
slot as shown in Figure 3. Feed cable into drum.
QUICK-CONNECT CABLE & TOOLS
Rotate pin one-half turn in either direction to
quickly add cable or tools.
Screwdriver Slot
LOCKED
Hash mark CLOSED aligned with L stamped on coupling.
Hash Mark
(Un-locked position)
UNLOCKED
Hash mark OPEN aligned opposite L stamped on coupling.
Coupling features stainless steel pin and spring: eliminates need for
punches, stands, or expansion pins.
Figure 3 – Disconnecting/Connecting Cable to Pigtail or
Tool
Hash Mark
(Locked position)
Screwdriver Slot
5