4" Center Drive Assembly; Ensamble De La Unidad Motriz Central De 4 - HYTROL TA Manual De Instalación Y Mantenimiento

• 4" Center Drive Assembly

44
30
31
41
40
Ref. No. Part No.
1 — Motor-C-face
— 030.7134 1/2 HP—230/460 VAC—3 Ph.—60 Hz.—TEfC
— 030.7324 1 HP—230/460 VAC—3 Ph.—60 Hz.—TEfC
— 030.7534 2 HP—230/460 VAC—3 Ph.—60 Hz.—TEfC
2 — Brake Kit (Used only on Incline Units A/R)
— 031.27595 1/2 — 1 HP
— 031.2795 1-1/2 — 2 HP
3 — Speed Reducer**
— R-00153-30R 4AC—RH—30:1 Ratio
— R-00164-30R 5AC—RH—30:1 Ratio
4 — Coupling Kit-Motor To Reducer
— 052.145 1/2 — 1 HP
— 052.146 1-1/2 — 2 HP
5 — Sprocket-Reducer**
— 028.115 50B15 x 1 in. Bore (4AC)
— 028.117 50B15 x 1-1/4 in. Bore (5AC)
6 — Sprocket—drive Pulley**
— 028.123 50B15 x 1-3/16 in. Bore
7 029.101 #50 Riveted Roller Chain
8 029.201 Connector Link—#50 Roller Chain
9 B-21330 4 in. dia. Ctr. dr. Pulley (fully Lagged) (Specify OAW)
10 B-06041 drive Plate Assembly—RH
11 B-06042 drive Plate Assembly—LH
12 010.103 3-Bolt flange Bearing—1-3/16 in. Bore
13 090.203 Shaft Key—1/4 in. Sq. x 1 in. Long
14 B-11982-R Motor Base Support Angle Assembly - RH Reducer
15 B-11974-R Motor Support Assembly - RH Reducer
16 B-11977 Reinforcement Bar
17 B-05965 Take-Up Bracket
Based on Standard Speed
**
Basado en la velocidad estándar

Ensamble de la Unidad Motriz Central de 4"

16
20
17
14
38
43
10
9
32
28
29
42
39
11
description
19
4
3
18
33
34 36 12 25
37 24 6
27
Ref. No. Part No.
18 B-06629
19 040.307
20 041.300
21 B-06090
22 B-06093
23 098.168
24 040.31115
25 041.200
26 041.919
27 B-04842
28 B-17254
29 B-05477
30 040.411
31 041.201
32 —
— B-22323
— B-05904
33 010.102
34 B-05958
35 B-05966
36 B-04655
37 B-04161
38 B-04287
39 B-04286
40 B-08337
41 B-08338-R
42 B-08338-L
43 B-08339
44 049.310
13
2
1
15
16
19 20
17
23
35
22
5
13
7
8
description
Motor Base Assembly (Specify OAW)
Motor Base Take-Up Bolt—3/8-16 x 2 1/4 in. Long
Motor Base Hex Jam Nut—Heavy-3/8-16
Chain Guard front Plate
Chain Guard Back Plate
Spacer - 13/32 in. I.d. x 1 in. O.d. x 1.539 in. Long
Hex Thin Head Bolt, 3/8-16 x 3 1/4 in. Long
Hex Jam Nut, 3/8-16
Acorn Nut, 3/8-16
11/16 in. Hex Idler Bracket
2-1/2 in. dia. Heavy duty Snub Idler (Specify BR)
Threaded Section Spacer (Specify OAW)
Take-Up Bolt—1/2-13 x 9 in. Long
Hex Jam Nut—1/2-13
4 in. dia. Take-Up Pulley
10 in. thru 18 in. drive Width (Specify)
20 in. thru 34 in. drive Width (Specify)
3-Bolt flange Bearing—1 in. Bore
Take-Up Plate Assembly
Upper Bearing Guide
Bearing Guide Spacer
Bearing Guide
Rear Guard (Specify OAW)
Bottom Guard (Specify OAW)
Bottom Angle Guard (Specify OAW)
Side Guard-RH
Side Guard-LH
formed Clip
U-Type Speed Nut-1/4-20
21
26