Tabla de contenido
Publicidad
TAbLE OF CONTENTS
INTROdUCTION
Receiving and Uncrating . . . . . . . . . . . . . . . . . . . .2
How To Order Replacement Parts . . . . . . . . . . . .2
Installation/Operation. . . . . . . . . . . . . . . . . . . . . . .3
Maintenance/Safety Labels . . . . . . . . . . . . . . . . . .3
Support Installation . . . . . . . . . . . . . . . . . . . . . . . .4
Ceiling Hanger Installation . . . . . . . . . . . . . . . . . .4
Belt Installation . . . . . . . . . . . . . . . . . . . . . . . . . 4,5
Conveyor Set-Up . . . . . . . . . . . . . . . . . . . . . . . . 4,5
Electrical Equipment . . . . . . . . . . . . . . . . . . . . . 4,6
Conveyor Start-Up. . . . . . . . . . . . . . . . . . . . . . . . .6
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Belt Tracking . . . . . . . . . . . . . . . . . . . . . . . . . . . 6,7
drive Chain Alignment and Tension . . . . . . . . . . .8
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . .8
Maintenance Checklist . . . . . . . . . . . . Back Cover
REPLACEMENT PARTS
4" End drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
8" End drive . . . . . . . . . . . . . . . . . . . . . . . . . 10,11
Underside Take-Up . . . . . . . . . . . . . . . . . . . . . . .11
4" & 8" Center drive . . . . . . . . . . . . . . . . . . . . . .12
4" Center drive Assembly . . . . . . . . . . . . . . . . . .13
8" Center drive Assembly . . . . . . . . . . . . . . . . . .14
Standard End Power feeder. . . . . . . . . . . . . . . .15
System End Power feeder . . . . . . . . . . . . . . . .16
Spanish Version . . . . . . . . . . . . . . . . . . . . . . 17
Ancho Total
Ancho de la Banda
Belt Width
6"
8"
10"
Bed Width
10"
12"
14"
OAW
Belt Width
12"
14"
16"
18"
20"
16"
18"
20"
22"
24"
INTRODUCTION
This manual provides guidelines and procedures for installing, operating,
and maintaining your conveyor. A complete parts list is provided with rec-
ommended spare parts highlighted in gray. Important safety information is
also provided throughout the manual. for safety to personnel and for proper
operation of your conveyor, it is recommended that you read and follow the
instructions provided in this manual.
• Receiving and Uncrating
1. Check the number of items received against the bill of lading.
2. Examine condition of equipment to determine if any damage
occurred during shipment.
3. Move all crates to area of installation.
4. Remove crating and check for optional equipment that may be fastened to
the conveyor. Make sure these parts (or any foreign pieces) are removed.
NOTE: If damage has occurred or freight is missing,
Contact your Hytrol Integration Partner.
• How to Order Replacement Parts
Included in this manual are parts drawings with complete replacement parts
lists. Minor fasteners, such as nuts and bolts, are not included.
When ordering replacement parts:
1. Contact dealer from whom conveyor was purchased or nearest HYTROL
Integration Partner.
2. Give Conveyor Model Number and Serial Number or HYTROL factory
Order Number.
3. Give Part Number and complete description from Parts List.
4. Give type of drive. Example-8" End drive, 8" Center drive, etc.
5. If you are in a breakdown situation, tell us.
Hytrol Conveyor
Company, Inc.
SERIAL #
24"
30"
28"
34"
2
Model
JONESbORO, ARKANSAS
123456
Model
XX
Publicidad
Capítulos
Tabla de contenido
