Impact Drilling - EINHELL TE-HD 18/12 Li Manual De Instrucciones Original

point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
6.2 Selector switch for driving/drilling/impact
drilling (Fig. 4/Item 2)
Caution!
Change the switch position only when the
equipment is at a standstill!
Drilling/Screwdriving:
For drilling/screwdriving, turn the rotary switch (2)
to position A.

Impact drilling:

For impact drilling, turn the rotary switch (2) to
position B.
Caution!
You only require slight contact pressure for ham-
mer drilling. Excessive contact pressure will place
unnecessary strain on the motor. Check drill bits
at regular intervals. Sharpen or replace blunt drill
bits.
6.3 Changeover switch (Fig. 5/Item 3)
Using the slide switch above the On/Off switch
you can select the direction of rotation of the
equipment and lock the equipment so that it can-
not be switched on accidentally. You can select
between clockwise and counter-clockwise rotati-
on. To avoid causing damage to the gearing, the
direction of rotation must only be changed when
the equipment is at a standstill. When the slide
switch is in the middle position, the On/Off switch
is blocked.
Danger!
To avoid danger, the machine must only be held
using the two handles.
Otherwise you may suff er an electric shock if you
drill into electric cables!
Anl_TE_HD_18_12_Li_Solo_SPK9.indb 20 Anl_TE_HD_18_12_Li_Solo_SPK9.indb 20
GB
6.4 On/Off switch (Fig. 5/Item 4)
Infi nitely variable speed control is possible with
the ON/OFF switch. The further you push the
switch, the higher the speed of the equipment.
Switching on:
Press the On/Off switch (4).
Switching off :
Press the On/Off switch (4).
6.5 Battery capacity indicator (Fig. 6/ Item e)
Press the button for the battery capacity indicator
(d). The battery capacity indicator (e) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too high. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
6.6 LED lamp (Fig. 6/Item 5)
The LED light (5) can be used in poor lighting
conditions to illuminate the area where you want
to drill or screw. The LED light (5) will come on
automatically as soon as you press the On/Off
switch (4).
6.7 Inserting a tool (Fig. 7)
Caution! Set the changeover switch (3) to its cen-
ter position whenever you carry out any work (for
example changing the tool, maintenance work,
etc.) on the equipment.
•
Clean the tool before fitting it and apply a thin
coating of bit grease to the tool shaft.
•
Turn and push the dust-free tool into the tool
mounting (f) as far as it will go. The tool will
lock automatically.
•
Check that the bit is locked in placed by
pulling on it.
- 20 -
21.08.2020 08:40:54 21.08.2020 08:40:54