GE GFDR485 Manual Del Propietario E Instalación página 22

Ocultar thumbs Ver también para GFDR485:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Instollotion
Instructions
CONNECTING
AN ELECTRIC DRYER (cont.)
CONNECTING
DRYER USING 4-WIRE
CONNECTION
(MUST BE USED FOR
MOBILE HOME INSTALLATION)
NOTE: Since January 1, 1996, the National Electrical
Code requires that new constructions
use a 4-wire
connection
to an electric dryer. A 4-wire cord must
also be used where local codes do not permit
grounding through the neutral.
3-wire connection
is NOT for use on new
construction.
Remove ground
Relocate green
strap and
ground screw here
discard. Keep
Hot Wire
green ground
Screw
GreenWire
screw
o II
Strain Relief
Bracket
Strain Relief
.-4 #!0 AWG minimum copper
conductors or 120/240V 30A
power supply cord kit marked
for use with dryers and provided
with closed loop or spade
terminals with upturned ends
(not supplied)
1. Turn off the circuit breaker(s) (30 amp) or remove
the dryer's circuit fuse at the electrical
box.
2. Be sure the dryer cord is unplugged
from the wall
receptacle.
3. Remove the power cord cover located at the
lower back.
4. Remove and discard ground strap. Keep the
green ground screw for Step 7.
5. Install 3/4 in. UL-recognized
strain relief to power
cord entry hole. Bring power cord through
strain
relief.
6. Connect power cord as follows:
A. Connect the 2 hot lines to the outer screws of
the terminal
block (marked LI and L2).
B. Connect the neutral (white)line
to the center of
the terminal
block (marked N).
7. Attach ground wire of power cord with the green
ground screw (hole above strain relief bracket).
Tighten all terminal
block screws (3) securely.
8. Properly secure power cord to strain relief.
9. Reinstall the cover.
NEVER LEAVE THE COVER OFF OF THE TERMINAL
BLOCK.
CONNECTING
DRYER USING 3-WIRE
CONNECTION
If required,
__ -:Green Ground
by local code,
_Screw
install external
ground (not
provided) to
grounded metal,
cold water
pipe, or other
established
ground
determined
by a qualified
electrician.
Ground
IIII
Strap
/11
Hot Wire "
e"
3/4" UL Recogn
Strain Relief
J
3 #]O"AWG minimum copper
f
9onductors or !20/240V 30A
power supply cord kit marked for
use with dryers and provided with
closed loop or spade terminals
with upturned ends (not supplied)
3-wire Connection
Not for use in Canada.
DO NOT use for Mobile Home Installations.
NOT for use on new construction.
NOT for use on recreational
vehicles.
NOT for use in areas where local codes prohibit
grounding
through
the neutral conduction.
1. Turn off the circuit breaker(s) (30 amp) or remove
the dryer's circuit fuse at the electrical
box.
2. Be sure the dryer cord is unplugged
from the wall
receptacle.
3. Remove the power cord cover located at the
lower back.
4. Install 3/4-in. UL-recognized
strain relief to power
cord entry hole. Bring power cord through
strain
relief.
5. Connect power cord as follows:
A. Connect the 2 hot lines to the outer screws of
the terminal
block (marked L1 and L2).
B. Connect the neutral (white)line
to the center of
the terminal
block (marked N).
6. Be sure ground strap is connected
to neutral
(center) terminal
of block and to green ground
screw on cabinet rear. Tighten all terminal
block
screws (3) securely.
7. Properly secure power cord to strain relief.
8. Reinstall the cover.
NEVER LEAVE THE COVER OFF OF THE TERMINAL
BLOCK.
22

Publicidad

Tabla de contenido
loading

Tabla de contenido