Revell Control NAVIGATOR Manual Del Usuario página 12

5F To start the rotors, move the control for thrust and rotation 2A to the bottom left
and move the control for forward/backwards and banking 2B to the bottom right at
the same time 5F. Attention: With both controllers in the bottom inside or outside
position, the rotors switch off instantly, even while in the air. In order to switch off the
rotors after landing, move the control for thrust and rotation 2A all the way down and
hold. Then move the controls 2A and 2B downward, inward or outward in order to switch
off the rotors. Attention! Never reach into the rotating rotor blades: Increased risk of injury!
5G To shoot photos and videos, a micro SD card must be inserted in the micro SD card
slot 1H. Please only use Class 10 HC memory cards. The memory card is not included.
Once you have finished flying, switch the model off first and then the remote control.
Unplug the battery from the model and remove the battery from the model.
6 TRIM ADJUSTMENT OF THE CONTROL
The model must be switched on first in order to connect it to the remote control.
Its adjustment is simple, but it requires some patience and a feel for it. Please observe
the following instructions precisely: Carefully move the thrust control up and raise the
helicopter approximately 0.5 to 1 metre in altitude.
6A If the model automatically moves slowly or quickly to the left or right ...
gradually press the trim for sideways flight 2E in the opposite direction.
6B If the model moves by itself slowly or quickly around its own axis ...
press the trim adjustment for rotation 2C incrementally in the opposite direction.
6C If the model automatically moves slowly or quickly forwards or backwards ...
gradually press the forwards/backwards trim 2D in the opposite direction.
7 FLIGHT CONTROL
The model is equipped with an automatic altitude control assistant that makes it possible
to learn how to control the model quickly and easily. The assistant is a sensor that can
measure the air pressure to within 10 centimetres of the exact altitude and thereby
automatically keep the quadrocopter at the specified altitude. Therefore, beginners can
concentrate on forward/backwards and banking.
Attention: Due to outside influences, the pressure inside the model may change,
causing the model to automatically rise or lower. This is not a defect. Briefly actuating
the control for thrust and rotation 2A is sufficient to counteract this.
Note: Only minimal corrections of the controls are necessary for a smooth flying behavior
of the model! The direction indication applies when the model is viewed from behind. If
the model is flying forwards towards the pilot, it must be moved in the opposite direction.
Switch on the model as shown in point 5 and start the rotators by moving the controls
2A and 2B to the bottom outside.
22
7A Take off or increase altitude by carefully moving the control for thrust and
rotation 2A forward.
7B Land or decrease altitude by moving the control for thrust and
rotation 2A backward.
7C Fly forward by moving the controller for forward/backward and sideways
flight 2B carefully forward.
7D Fly backward by moving the controller for forward/backward and sideways
flight 2B carefully backward.
7E Fly to the left by moving the controller for forward/backward and sideways
flight 2B carefully to the left.
7F Fly to the right by moving the controller for forward/backward and sideways
flight 2B carefully to the right.
7G Turn the model around to the left by moving the control for thrust and rotation 2A
to the left.
7H Turn model around to the right by moving the control for thrust and rotation 2A
to the right.
7I The camera takes a photo when the button 2G is pressed. Ensure beforehand that
there is a micro SD card in the micro SD card slot 1H.
7J The camera begins recording a video when the button 2I is pressed. Pressing it again
stops the recording. The remaining recording time for the memory card is shown in
the top centre of the display. It is also recognisable from the timer counting down for
the recording.
7K Briefly pressing vertically (about 0.3 seconds) on control 2A activates headless mode.
Headless mode supports beginners in the initial stages. Regardless of where
the quadrocopter turns, the direction of flight always corresponds exactly to the
direction specified with the control for forwards/backwards and sideways move-
ment 2B. An example: If the model were to be turned 180° and flown towards
the operator, the operator would have to „convert" the forwards/backwards and
sideways movement accordingly. This is no longer necessary if headless mode is
activated, as the internal processor always converts the control directions automatically.
Pressing the 2A button again deactivates the mode.
Attention: The model „notes" the forwards direction during each switch-on. This
means that the operator must not turn when controlling the model, as this would
change the concept of „forwards" and „right/left" in relation to the model. If the operator
changes position and wants to use headless mode - or if the control direction is no longer
correct due to a collision, the model must be restarted.
7L Switch for GPS Hold 2J: The GPS flight support can be activated and deactivated
with the switch for GPS Hold. GPS is activated when the switch is moved upward.
GPS Hold ensures that the model is only moved when it is controlled. External
influences such as wind are compensated for. Flying without GPS Hold is only
recommended for experienced pilots.
7M Switch for Coming Home 2K: With activation of the switch for Coming Home
(switch in upward position), the model automatically returns to the starting point
(or the position at which six satellites were first found) and lands. The model
climbs or drops to a height of approximately 20 metres and returns to the starting
point. In the process, look out for any obstacles in the flight path and intervene as
necessary with controls 2A and 2B. After the automatic landing, the rotors continue
to turn slowly. Switch them off as described in section 5.
7N Follow Me: Vertically pressing control 2B activates Follow Me mode (message in
the display). This means that the model maintains the same distance and elevation in
relation to the remote control and follows its movements. Never lose eye contact
with the model and do not use the display to fly. Any movement with the controls
switches back to normal mode (brief message in the display).
23