Geneva AeroSphère Large Guía De Configuración página 7

DISPLAY
The color of the Geneva logo shows the operation status of the device.
COLOR STATUS
off Device is powered off
yellow Device is starting up
green ( constant ) AirPlay or DLNA, connected to the Wi-Fi network
NYLLU  ÅHZOPUN  AirPlay or DLNA, waiting to connect to the Wi-Fi network
blue ( constant ) Bluetooth, connected
IS\L  ÅHZOPUN  Bluetooth, connecting or pairing
pink Line-In
ONLY WITH AEROSPHÈRE BASE
red Audio CD ( AeroSphère Base )
light blue FM or DAB+ ( AeroSphère Base )
pink Line-In ( AeroSphère Base )
YLK  SPNO[ IS\L  WPUR  ÅHZOPUN  Waiting to connect to the AeroSphère Base
ADVANCED
green / yellow blinking Failed to connect to a Wi-Fi network
NYLLU  ÅHZOPUN  [PTLZ  Successfully connected to Wi-Fi network
NYLLU  YLWLH[LK ZOVY[ ZPUNSL ÅHZO  Wi-Fi setup in progress ( WPS method )
NYLLU  YLWLH[LK ZOVY[ KV\ISL ÅHZO  Wi-Fi setup in progress ( webpage or WAC method )
LINE-IN
The 3.5 mm analog audio input on the back of the AeroSphère speaker can be used for external audio sources. Press
There are two buttons on the remote control: the upper button selects the analog audio input on the AeroSphère speaker, the lower
button selects the analog audio input of the AeroSphère Base.
BACK PANEL
POWER BUTTON POWER ON / OFF
WPS setup ( push button once )
>PÄ :L[\W I\[[VU
WAC setup / Network webpage setup ( hold button for 10 sec )
Line-in connector Analog audio input ( stereo ), 3.5 mm connector
AC power input connector AC power input ( 100 - 240 VAC, 50/60 Hz )
10
V GETTING STARTED WITH THE AEROSPHÈRE BASE
Time required: 5 minutes
Once completed: you have connected all wires and you are ready for the Wi-Fi setup.
OVERVIEW
The AeroSphère Base adds FM, DAB+ and audio CD functionality to all
AeroSphère Base speakers in the same home network. The AeroSphère
is controlled with the remote controls of the AeroSphère speakers, or
with the AeroSphère iPhone and Android App.
No separate remote control is needed to operate the AeroSphère
Base. The AeroSphère Base has no remote control sensor. You
can control the AeroSphère Base functionality directly from the
AeroSphère speakers.
CONNECTING ALL WIRES
Attach the FM / DAB+ Antenna
1. Screw the enclosed FM/DAB+ antenna into the antenna connector
on the back.
2. Screw the two rods into the end of the antenna
3. Place the end of the antenna at least one meter away from the
AeroSphère Base. The long wire allows you to place the antenna in
a location where you have the best FM/DAB+ reception. Note that
only the two rods at the end of the wire is the actual antenna.
Connect the power
1. Connect the AC power adapter to an AC wall outlet. Then connect
on the remote control.
the other end of the AC power adapter into the back of the
AeroSphère Base.
2. Move the power switch to the ON position. The AeroSphère Base is
a network device and will always stay connected to the network.
ENGLISH
Next: Wi-Fi Setup
Now you are ready to connect the AeroSphère Base to your Wi-Fi
network—go to the next chapter for more details.
Do I need to configure the AeroSphère system?
5V @V\ KV UV[ OH]L [V KV HKKP[PVUHS JVUÄN\YH[PVU 6UJL [OL )HZL HUK
the Speakers are connected to the Wi-Fi network, the AeroSphère Base
ÄUKZ HSS H]HPSHISL (LYV:WOuYL ZWLHRLYZ automatically.
11